Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, farmland irrigation,MilwaukeeBooster pipeline pump, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid peopleMilwaukee,　　Ensure that the power supply voltage is adjusted to the standard power supply to solve the problem.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Peje,　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　Be sure to choose a pump that is more suitable for use.

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　The sub bearing and cylindrical roller bearing can bear the maximum axial and radial loads of the pump. The bearing is lubricated with grease. The two ends of the bearing body are provided with sealing end caps, labyrinth sleeves and labyrinth rings, which can effectively prevent dirt such as mineral slurry from entering the bearing ensure the safe operation of the bearing and have a high service life.　　It is located in the middle,MilwaukeeCentrifugal slurry pump,　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump so it seems that many regions have good effects when using it.technological innovation, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft,MilwaukeeBaigang deep well pump, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　With water, you can start working.

　　 To ensure the efficient operation of the submerged slurry pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeEncyclopedic knowledge　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　In order to maintain the original treated water volume without increasing the number of water pumps, the liquid level in the storage tank can be increased by adjusting the floating ball in the liquid tank. After the liquid level in the storage tank is increased, the head at the intersection of the two curves becomes smaller and the flow remains　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appearMilwaukee,　　Stability and reliability of seals between pump bodies.　　How to avoid this situation when the equipment is in use.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.