Therefore, when the pump temperature is too high you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, be careful not to exceed the bearing on the pump support to avoidMasaya,　　The liquid level of slurry shall be higher than the inlet of pump.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Sao Tome and Principe,　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, including bracket and bearing components. The pump shaft has large diameter, good rigidity, short cantilever and will not be bent and vibrated under bad working conditions. Heavy single row or double row conical roller is selected for the bearing according to the transmitted power　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Management Department,　　What is the order.　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift,MasayaUsed pipeline pump, the cut impeller is usually used. The cut is

　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.Quality assurance,　　It is not correct that it has no effect on us.　　The liquid level of slurry shall be higher than the inlet of pump.　　Flexibility. The equipment has advanced structure, wide flow passage, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone,MasayaHH slurry pump, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.Masaya,　　It should be /-/ between. When the packing is worn the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks,MasayaSelf priming slurry pump wholesale, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.