The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　Potential energy, pumping water up high. However, once the pump can not absorb water,ciudad obregon Submersible sewage pump,ciudad obregon Corrosive pipeline pump, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?ciudad obregon ,　　 the full-automatic control cabinet can be equipped according to the needs of users to automatically protect the water leakage, electric leakage, overload and over temperature of the pump which improves the safety and reliability of the product.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorBaden Baden Airpark,ciudad obregon Screw deep well pump,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　Carbon, building materials chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.

　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　Clean up the silt and other obstructions in or around the water pump.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellermarket price,　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, wrap the insulation layer and sheath layer wipe the wire core with alcohol (or hydrochloric acid), and dry it naturally.　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times

　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.assets,　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Water pump control cabinet Time control: the chassis panel is equipped with a time setting button and a display. The user can control the opening and closing of the water pump according to the timing needs. It is suitable for the control of various timed or regular intermittent working modes.　　In the application of pumps, our basic survival is a problem.ciudad obregon ,　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, When δ= A (. ~ mm　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.