That is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict so that the molten salt has strong oxidizing power, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide which is easy to be removed during acid pickling. Due to the action of high temperature, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching, firstly lift the parts basket into the tank, stop above the horizontal plane close the tank cover, Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable, safe,The heat-treated alloy should be DEG at low temperature; Annealing treatment at the temperature of F, then rapid cooling and water quenching. This treatment is applied to solid melt annealing and stress relief. Stress relief treatment, such as below DEG; F, which is easy to lead to the precipitation of harmful metal or non-metallic phases.Meet the needs of architects and structural designers.Kombissiri,. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, the scrap iron will cause rust on the surface of the steel pipe. Therefore, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities, and who should be responsible for whose achievements. You can't let steel mills, pipe factories, or users bear the liability for compensation!Clamping connection steps: cut off the pipe according to the required length. When breaking the pipe, it shall not be too large to prevent the pipe from being out of round.The recrystallization temperature changes with the shape variable. When the shape variable is %, the recrystallization temperature drops to ℃, and the recrystallization annealing temperature of cold deformed austenitic stainless steel is ~ ℃. At ℃,Cerrik1Cr13 stainless steel pipe, it needs to be kept warm for h, fully burned at ℃, and then water-cooled.

Stainless steel pipe, which was consumed and used at the end of the s is a rebirth group emerging in today's pipe range. It has been widely used in the construction of water supply and direct drinking water pipelines. Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing wall thickness and money, so as to facilitate further implementation. In order to promote stainless steel pipe, since the s, China has started to reduce wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical effect of stainless steel pipe makes the stainless steel pipe lose its application and expand quickly. There are various connection modes of stainless steel pipes. The rare types of pipe fittings include contraction type, compression type, union type, push type, push thread type, socket welding type, union flange connection, welding type and derivative series connection mode combining welding with traditional connection. These connection methods have different application ranges according to their principles, but most of them are convenient, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber, nitrile rubber and EPDM that meet the requirements of national specifications, which eliminates the worries of users. In the construction of water supply pipe system, due to the glorious history of galvanized steel pipe, all kinds of new plastic pipes and composite pipes have been lost and developed rapidly, but they are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. In direct drinking water, hotels and public places at the international level have been equipped or are equipped with direct drinking water pipelines. In many cases, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability in high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first. It has been proved by engineering theories at home and abroad that it is not only one of the new,CerrikTP347H stainless steel pipe, energy-saving and environmental protection pipes with good comprehensive function of water supply, but also a very competitive water supply pipe, which will play an unparalleled role in improving water quality and improving people's living standard.The surface of stainless steel contains acid, alkali and salt substances (such as alkali water and lime water splashing on the decoration wall), mainly in key parts such as high temperature section of superheater and reheater.Management DepartmentChloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, the welded junction can usually be rotated for welding, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.property right,Model & mdash; It has better temperature resistance.Selection process of stainless steel pipe water supply pipe.. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, the scrap iron will cause rust on the surface of the steel pipe. Therefore, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities, and who should be responsible for whose achievements. You can't let steel mills pipe factories, processors, or users bear the liability for compensation!Cerrik,Chloride ions exist in the service environment. Chloride ions exist widely, such as salt,CerrikHow many stainless steel plates, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Construction materials shall be prepared and delivered to the site according to the data scheme, and shall be supplied according to the scheme.In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.