After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃ and the solution time is min. Then dry.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, etc.). Due to the reasonable section shape profiled steel plate, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete which is convenient for settingSt.Petersburg, As long as the pipe material is high-strength alloy steel, including alloy steel pipes with temperature resistance, pressure resistance, wear resistance and low temperature resistance, the welding process shall be focused on preventing the tendency of martensite structure and cracks due to welding high-temperature operation. The general process requirements are that the welding rod shall be selected and baked as required and sent to the welder for use. The oil and water shall be removed before welding on both sides of the weld Rust and sundries shall be removed and cleaned. The welding line energy shall be as small as possible to minimize the swing during the welding process. The arrangement of the last weld shall have annealing effect on the heat affected zone as far as possible. Slow cooling after welding, cover with asbestos cloth, etc.I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.Nuevo Imperial,Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole,High quality brand,I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Generally, there are many passivation methods for alloy tubes, damage and blanking,St.PetersburgGH4169 superalloy tube, and increase the labor cost of material cleaningQuality inspection report,Key technical characteristics of alloy pipe: Because the zinc coating has excellent ductility, it can be formed by cold stamping, rolling,When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project,St.Petersburg022cr17ni12mo2 seamless pipe, there are many things that must be paid special attention to. Let&#;s take you to know:It is widely used in various fields of national economic construction, such as buildings, bridges, power stations,St.PetersburgSquare rectangular hot dip galvanized welded pipe, oil drilling platforms, vehicles, highways, subways, steel structure plants and large warehousesSo why is the alloy pipe easy to rust after being pickled and passivated by the software?