Application characteristics of I-beam:Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Acunia CityThe reinforcement mesh is used for embankment protection or for the protection of the whole riverbed and river bank, which is more suitable for the river channel with relatively gentle original bank slope. Taking the design dry water level as the boundary, the upper part is slope protection works and the lower part is foot protection works.Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementAbu Tij, which can not only save resources,Acunia CityAlloy pipe for power plant, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.I-beam is mainly used in building structure, curtain wall engineering mechanical equipment and vehicle manufacturing.

The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -. According to the purpose, the welded pipe has general purpose and high temperature and high pressure. The pipe used in the latter is often special alloy steel. The problem of shrinkage cracks in the welding process and the mechanical properties of the pipe in the heat affected zone must be considered and solved, and the mechanical properties of the pipe in the heat affected zone will not be greatly changed due to the influence of welding operation.Greatly reduce the environmental pollution caused by abrasion, damage and blanking, and increase the labor cost of material cleaningAnalysis project,Generally there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Inspection basis,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.There are many processes in the process of welded pipe processing, and every detail needs our attention. Welded pipes need to be treated by various processes before application. Heat treatment of welded steel pipe is an important link in the process of welding steel pipe. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and the metal properties are controlled by changing the metallographic structure on the surface or inside of the material.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %,Acunia City25# I-beam manufacturer,The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,Passivation treatment operation of alloy pipeI-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.