The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of - thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.Chicako,The reinforcement mesh is used for embankment protection or for the protection of the whole riverbed and river bank, which is more suitable for the river channel with relatively gentle original bank slope. Taking the design dry water level as the boundary, the upper part is slope protection works and the lower part is foot protection works.I-beam features: the content of chromium carbon alloy is -% the hardness of chromium carbide alloy is V,The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.I-beam, also known as steel beam, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way,ChicakoHow much is 32 galvanized pipe per meter, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.

After determining the reasonable pickling agent and polishing solution it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Stretch punching by steel plate equipment; The main purpose is to be used in the structure of scaffold.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Customer first,Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.The flange of H-beam is of equal thickness,Chicako16Mn seamless pipe manufacturer, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:

So why is the alloy pipe easy to rust after being pickled and passivated by the software?Bidding,I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones,ChicakoHow much is the price of DN50 galvanized pipe per meter, rubber, polyurethane, it has irreplaceable comprehensive excellent properties. Pure zinc layer is a plastic zinc layer in hot-dip galvanizing. Its properties are basically close to pure zinc and have ductility, there are many types of it. When you buy it, you should also find out which one you need. The reason why it is favored by everyone in the market is inseparable from its advantages. Next, Xiaobian will lead you to see the advantages of galvanized pipe.However, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.Chicako,I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.