Function of I-beam: where is I-beam mainly used?Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Gillard melena,During the heating and cooling process of structural welded pipe workpiece, due to the inconsistent cooling speed and time of surface layer and core layer, the temperature difference will be formed, resulting in uneven volume expansion and contraction, resulting in stress, namely thermal stress. Under the action of thermal stress, the starting temperature of the surface layer is lower than that of the core layer, and the shrinkage is greater than that of the core layer, making the core layer stretch. At the end of cooling, the surface layer is compressed and the core is stretched because the cooling volume contraction of the core cannot be carried out freely. That is, under the action of thermal stress, the surface of the workpiece is compressed and the core is pulled.Requirements of alloy tubes for low and medium pressure boilersMukacheve, Small longitudinal crackb. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration,Gillard melenaHow much is DN65 galvanized pipe, and it is very easy to manipulate the welding quality.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.

With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.Seamless pipe is made of steel block or solid pipe blank, and then made by hot rolling, cold rolling or cold dial. Seamless pipe plays an important role in China&#;s steel pipe industry. Seamless pipe production processes are relatively rich, the I-steel structure can increase the service area by %Function of I-beam: where is I-beam mainly used?→ compared with the concrete structure, reduce the self weight of the structure by % - % and reduce the structural design internal force.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe,Gillard melenaWhere is 40CrMo seamless pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.

Passivation treatment operation of alloy pipeInstallation material list,It can withstand continuous moderate impact and can provide composite plates of various thicknessesGalvanized pipe can be seen from its name. It is a square pipe type. Many materials can form galvanized pipe body. It is used for what purpose and where. Most galvanized pipes are steel pipes. After unpacking, leveling, crimping and welding, they form round pipes, which are rolled into square pipes, and then cut into the required length. Generally, there are galvanized pipes in each package. In terms of spot, most of them are in large specifications, ranging from * * .- to * * - Galvanized pipes are divided into structural galvanized pipes, architectural galvanized pipes, mechanical galvanized pipes, etc.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.Gillard melenaThe production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate,Gillard melenaQ235B hot dip galvanized welded pipe, etc.). Due to the reasonable section shape, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for setting