Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materials→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.VaregumThe use of welded steel mesh can make the project construction convenient. As long as the welded reinforcement mesh is laid as required, the concrete can be irrigated, eliminating the links such as on-site cutting, placing and binding of reinforcement one by one.Requirements of alloy tubes for low and medium pressure boilersAguilares, it has the advantages of low cost high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

I-beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.The third is the welding machine,VaregumIncoloy800 alloy pipe, which must ensure reliable performance and meet the process needs; The welding machine must have qualified ammeter and voltmeter to ensure the correct implementation of welding process. The welding cable shall not be too long, and the welding parameters shall be adjusted when it is too long.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.system,Classification introduction Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, small types, multi specifications and high precision. Therefore, it is widely usedBecause all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.

What are the requirements for alloy pipe construction accessoriesbuild,The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method. Spiral seam high-frequency welded steel pipe (sy- for pressure fluid transportation is a spiral seam high-frequency welded steel pipe used for pressure fluid transportation, which takes hot-rolled steel strip as pipe blank, often warm spiral forming and high-frequency lap welding method. The steel pipe has strong pressure bearing capacity and good plasticity, which is convenient for welding and processing; After various strict and scientific inspections and tests, the application is safe and reliable,Varegumtwo hundred × How much is 100 I-beam per meter,VaregumInconel 601 alloy pipe, the diameter of steel pipe is large, the transportation efficiency is high, and the investment in laying pipeline can be saved. It is mainly used for laying pipelines for transporting oil, natural gas etc.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Varegum,In order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Stages needing attention in the production and manufacture of alloy tubesWhen we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know: