Alloy tube is widely used in our daily life,Kingston ParkPrice of 34CrMo4 seamless pipe, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Kingston Park,Generally in terms of strength, the production efficiency is very high, and there are many varieties and specifications. The demand for RHS by equipment and capital is very small, which is suitable for the production of small galvanized steel pipe plants. However, the strength of steel is much lower than that of seamless steel pipe. It is mainly used for drying, redox method and characteristic table.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Mikkeli, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.→ compared with general section steel, it has the advantages of low cost, and saves about % of the manufacturing cost of steel structure.The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.

Performance parameters and application scope of I-beamThere are many processes in the process of welded pipe processing, and every detail needs our attention. Welded pipes need to be treated by various processes before application. Heat treatment of welded steel pipe is an important link in the process of welding steel pipe. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and the metal properties are controlled by changing the metallographic structure on the surface or inside of the material.It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles,Kingston Park16Mn seamless pipe factory, highways, subways, steel structure plants and large warehousesplan,a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);What is nitriding of alloy pipe

Function of I-beam: where is I-beam mainly used?Quality documents,Key technical characteristics of alloy pipe:The use of hot dip galvanizing has expanded with the development of industry and agriculture. Therefore hot-dip galvanized products have been widely used in industry (such as chemical equipment, petroleum processing, marine exploration, metal structure, power transportation, shipbuilding, etc.), agriculture (such as sprinkler irrigation, heating room), wire casing, scaffold, etc.), bridges, transportation, etc. because hot-dip galvanized productsAll the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation showing a 'high mountain' shape.Kingston Park, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.At the same height light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.