Although the opening continued the weak trend, the intraday transactions improved, and the prices of some copper bar manufacturers rose. From the specific situation, although the manufacturer feedback that the shipment is average, the mentality is relatively calm, the market inventory is not much, and the manufacturer is not willing to significantly reduce the price. In terms of the market, the transaction of strip steel is better than other steel varieties, and the downstream mainly focuses on callback buying without panic inventory clearing. It can be seen that although the steel market continues to shake, the overall demand for strip steel remains in a good state.The blowing mouth of the welding tool should not be too small to avoid excessive concentration of heat.Antipolo,When the copper tube is heated and the flux melts into liquid, place the preheated electrode on the welding point immediately. As soon as the electrode begins to melt, move the flame nozzle back and forth until the solder flows into the gap between the two tubese the flame, let the solder contact the welding point, and then remove it after a few seconds. If it is suspected or found that there is still a gap between the two pipes. It can be heated again to make the flame nozzle move continuously at two points. A small amount of solder can be added.Disadvantages of copper pipe As far as copper pipe is concerned, the cost of copper pipe is much higher, and the connection at the copper pipe interface requires high construction technology level.Faya,The main force of iron ore futures closed at in The closing price of the day today was the same as that of the previous trading day, including * * * * * * * , settlement price , trading volume , and position volume . The intraday tradg volume decreased by compared with the previous trading day, and the position volume decreased by compared with the previous trading day. After six consecutive days of downward adjustment, there was a rebound at the bottom of the session today, but it was corrected again later, and the closing was flat.In Jiangyin market, another distribution center, the overall inventory of the current circulation link is about tons, slightly lower than the normal level. At the beginning of this week, the price gap between Jiangyin prices and those in the north has also been able to correspond to the slightly lower circulation inventory. However, from the perspective of the policy port of the steel plant, the overall production situation of Nangang, Hengrun,Antipolo5083 aluminum bar, Dada, etc. is relatively normal, and the amount of resources in the later period remains stable. The overall inventory of Lecong market remains at about to tons, which is a medium normal level, and the recent spot price of Lecong market has a large gap with that of the north.At present, the fundamentals faced by the domestic copper bar market are still mixed. On the one hand, the market supply is expected to shrink, but on the other hand, the northern market has entered the off-season of demand, and the market s expectation of future demand is pessimistic. In the short term, domestic steel prices will enter the operating track of range consolidation. To sum up, considering the current situation of demand and inventory in the steel market, it is difficult for the steel market to make a breakthrough. As the th National Congress of the Communist of China is approaching, environmental protection phenomena such as steel mills are still going on, and black series speculation is still taking place. But personally, the fluuation range of the market in this region is limited,Antipolo7075 aluminum pipe, and businesses can operate flexibly on a short-term basis, and the shipment transaction is * * *.

The blowpipe shall be perpendicular to the lead pipe during welding and the flame shall be moved continuously to prevent local overheating and the flux from carbonizing before filler metal is added.{} The copper pipe welding can be divided into soft welding and hard welding. The soft welding temperature is lower than ℃, and the hard welding temperature is higher than ℃. Hard welding is usually used for silver gold, steel, copper and other metals. Its welding points are much stronger than soft welding, and its shear strength is - times that of soft welding.With the advent of heating season the raw material support of red copper row is weak. Under the influence of heating season and environmental protection production restriction, and the demand for iron ore was weakened. In addition, the production restriction policy was issued in Tangshan today. From : on October to : on October , the production restriction measures specified in this Notice were implemented.Design brand,The blowpipe shall be perpendicular to the lead pipe during welding, and the flame shall be moved continuously to prevent local overheating and the flux from carbonizing before filler metal is added.[] Welding process of copper pipe Clean the end and seven ports of steel pipe with steel wool. Do not use abrasive cloth or abrasive paper to clean, because it will affect the clean interface and result in poor welding effect.When welding, just add enough filler metal to fill the capillary gap. Too much filler metal will only form a ball at the bottom of the joint or run into the pipe.

Advantages of red copper tube Durability: copper has stable chemical properties, integrating cold resistance, heat resistance, pressure resistance, corrosion resistance and fire resistance, and can be used in different environments for a long time.Create brilliance,Today, the price of tube billets is up and down. At present, Jiangxin hot rolling is yuan, Dongfang hot rolling yuan is down yuan, Luli hot rolling yuan is down yuan, Tiangang hot rolling an is down yuan, production is stopped in mid January, Weigang hot rolling yuan is up yuan, continuous casting yuan is up yuan Huaigang yuan is up yuan, Zhongtian yuan, Changqiang yuan, Linggang yuan.Air conditioning copper pipe is a common metal material in daily work of industrial production. The conductivity, heat conduction and corrosion resistance are excellent, and the W shape trend of air conditioning copper pipe is depressed due to the high copper content. Good machinability, fusion welding and brazing are very good. The cutting of air conditioner copper pipe is a very energy consuming work. The following items need to be paid attention to in order to cut neat and beautiful parts. Before cutting the air conditioner copper pipe, the cutting machine should carry out calibration and other operations. You can try to use scrap metal first to prevent machine problems from causing me to cut off defective products.Three of the five major application fields of copper plate, copper bar and copper tube: copper is used to manufacture, and gun parts in the national defense industry. Every million rounds of copper are produced, - tons of copper are needed.Antipolo,The conductive production of copper tube is the latest method for this method. It is the production of nanocrystalline copper materials with conductivity. Because this raw material is very special, and copper ions can be separated by conductivity, so that copper tubes can be produced with the separated copper ions. This method is very complex, so only advanced foreign countries can use this production method.Let s elaborate on the advantages of copper pipe materials: copper pipe floor heating refers to a heating method that uses hot water as the thermal medium, circulates in the copper pipe heating pipe, heats the floor, and heats the floor through the ground in the form of radiation and convection heat transfer. I. The copper tube has fast heat dissipation effect and strong heat resistance. Even under the condition of high temperature water supply,Antipolo12CR1MOV alloy plate, the service life of the floor heating tube will not be affected. Two. Copper pipe is a metal pipe, it is not easy to leak. Three. High temperature resistance, high pressure resistance relative to any ordinary plastic pipe. Copper tube floor is warm and resistant to high temperature and pressure. Four. Long service life. Five.Do not store too many other products, especially other acid materials and alkali materials, in the warehouse to prevent mutual reaction.