it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment

After determining the reasonable pickling agent and polishing solution,Tonara42CrMo seamless pipe factory, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, gas wastewater, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Tonara,The production methods of seamless pipe are roughly divided into cross rolling method and extrusion method. The cross rolling method is to drill the tube with a cross roll, and then extend it to the rolling mill. This method has fast production speed, but has high requirements for the workability of the blank. It is mainly suitable for the production of carbon steel and low alloy steel pipes. The extrusion law is to pierce the blank or ingot with a punch, and then squeeze it with a steel pipe with an extruder. The efficiency of this method is lower than that of cross rolling method. It is suitable for producing high-strength alloy steel pipe. The billet or ingot must be heated before cross rolling method and extrusion method. The produced steel pipe is called thermal correlation. Steel pipes produced by hot working can sometimes be cold worked as needed. There are two methods of cold working. One is cold drawing. In other words, pull the pipe to the pipe and tilt it to make the steel pipe gradually thinner and longer. Another method is cold rolling. The method of applying the hot smoke invented by brother to cold processing. The cold working of seamless pipe can improve the dimensional accuracy and finishing of steel pipe, and improve the mechanical properties of materials.Classification introductionDori, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.H-section steelAlloy pipes can be used for heating (cooling) projects.

The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.In order to improve the corrosion resistance of steel pipe, the general steel pipe (black pipe) is galvanized. The galvanized pipe is divided into hot-dip galvanizing and electric steel zinc. The hot-dip galvanizing layer is thick and the cost of electric galvanizing is low, I-beam has no specific composition and performance series.Where is it,I-beam is mainly used in building structure,Tonara12Cr1MoVG thick wall seamless pipe, curtain wall engineering, mechanical equipment and vehicle manufacturing.What should we pay attention to in the production of alloy pipeThe production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.

All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.supply,H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type,Tonara25 galvanized pipe 6 meters, how much is it, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingWhat is the of defect detection of seamless pipe? Magnetic particle testing or penetrant testing of seamless pipes can effectively find surface defects such as cracks, folds, double skin, hair lines, pinholes and so on. Because of its high detection sensitivity, magnetic particle detection method should be preferred for ferromagnetic materials. For non ferromagnetic materials, such as stainless steel seamless pipe, penetrant testing method is adopted.The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.Tonara,What are the uses of I-beam?Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementWhen selecting I-beam in structural design, chemical properties, weldability and structural size.