H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.→ the two surfaces of the flange are parallel to each other, making it easy to connect,KayPrice of galvanized pipe in 2021, process and install.Kay,The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society, Domestic hot welded pipe has gradually formed a situation to replace smooth pipe.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance simple construction, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel cost saving and light structural weight in all directions, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.Zajas,Requirements of alloy tubes for low and medium pressure boilersPerformance parameters and application scope of I-beamIt is widely used in various fields of national economic construction, such as buildings bridges, power stations,KayHow much is 6 meters of one inch galvanized pipe, oil drilling platforms, vehicles, subways,Kay40CrMnMo alloy pipe, steel structure plants and large warehouses

C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover it has good versatility and combination,Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress, that is, thermal stress.Classification introductionBecause the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, chemical properties, weldability and structural size of I-beam.

The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.Statistics,Stages needing attention in the production and manufacture of alloy tubesGalvanized pipe can be seen from its name. It is a square pipe type. Many materials can form galvanized pipe body. It is used for what purpose and where. Most galvanized pipes are steel pipes. After unpacking, leveling, crimping and welding, they form round pipes, which are rolled into square pipes, and then cut into the required length. Generally, there are galvanized pipes in each package. In terms of spot, most of them are in large specifications, ranging from * * .- to * * - Galvanized pipes are divided into structural galvanized pipes, decorative galvanized pipes, architectural galvanized pipes, mechanical galvanized pipes, etc.What are the uses of I-beam?Kay,It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingI-beam is widely used