Look at the section of the board.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Hartsfield,Solid wood flooring Generally, or wear-resistant paper is not used.Low density board (medium density board is rarely used), and the number of wear-resistant revolutions is usually between - revolutions.The edges and corners will be worn after being used for one or two years at most.With Hunan, Hubei, Shandong Liaoning, Jilin and Heilongjiang as the gathering points, the suburbs of Beijing are still rampant.Low quality, not environmental protection, government departments are strictly investigating and dealing with it.Such illegal businesses only take into account short-term interests and have no after-sales service guarantee. The price ranges from to yuan.Al-Rakka, Soak in waterLaminate flooring has reached grade B and has higher flame retardant performance, which is safer than other kinds of wood flooringNeedless to say, for a long time, the lacquered cloth market was occupied by low-grade unlined lacquered cloth produced in Taiwan and other overseas countries, which is made of poorly processed and Recycled PVC. It does not meet the national standards for plastic coiled materials at all, so its service life is short, not comfortable to use.

Service is not only related to the guarantee of product quality, but also the performance of corporate image.Some deformation, warping and cracking of floor products appear soon after installation, many of which are caused by improper installation.Therefore whether the service is professional or not also affects the performance of products. Dust-free installation is popular in floor installation. Dust pollution in home decoration can not be underestimated. For example, in floor installation engineering, sawdust and dust will inevitably appear and float in the air, and its harm is also long-term and serious.People who move into new houses often suffer from a strange disease of 'new house syndrome'. For example, when they get up every morning, they feel suffocated, nausea, and even dizzy;Easy to catch a cold;I often feel uncomfortable in my throat, poor breathing, dizziness and fatigue after a long time.This is because the respiratory tract is infected, and the biggest inducement is the invasion of dust suspended in the air for a long time.In order to avoid dust pollution, it is best to choose dust-free installation.Because SPC floor is composed of wear-resistant layer, rock mineral powder and polymer powder, it is certainly not easy not to be waterproof. There is no need to worry about the deformation and mildew of the floor by small blisters.Waterproof and mildew removal are very good, so toilets, restaurants, kitchens and living balconies can be used. Beautiful and diverse colors, seamless splicing construction, convenient and fast installationhow much, After days, maggots appeared on the floor.This problem is because the floor contains a lot of impurities. High elasticity and super impact resistance.Pengpai stone plastic floor has soft texture, so it has good elasticity. It has good elasticity recovery under the impact of heavy objects. Its foot feeling is comfortable, which is called 'soft gold of ground materials'.Even if you fall down, it is not easy to get hurt. Installing stone plastic floors at home can protect the elderly and children.You can take some steps to ensure a smooth and seamless installation: remove the base plate and door frame before starting.This will make it easier for your installation team to get the perfect fit.No matter what kind of floor you are currently using, thorough vacuuming will make the rest of the work easier.Ask the installer in advance whether to remove the old floor or decide by himself.

About solid wood composite floor.index, Remove spots and stains with special floor cleaner.Do not clean with items with damaging properties, such as metal tools nylon friction pads and bleaching powder. Check whether there is sand on the ground and carry out curing treatment in time.The quality of laminate flooring can also be distinguished by some methods:Hartsfield,The laminate floor is composed of wear-resistant layer, decorative layer, base material and balance layer.The wear-resistant layer, decorative layer and balance layer are manually printed, and the base material is made of fast-growing forest materials. The cost is lower than that of solid wood flooring. At the same time, and the relative cost performance is high.Due to the different base materials, the price difference is obvious, and there is more room for customers to choose, which is suitable for people at all levels. Test: for the ground lacquer cloth with thin thickness, you can tear it by hand. If it can be easily torn off, the tear strength of such ground lacquer cloth can not meet the requirements. After gently rolling up and pressing down if it can not be restored to the original state and leave an indentation, such a product has poor softness.If the layers can be torn by hand, it indicates that the product layers are not well combined, and stratification will soon occur in future use.Plastic floor paint cloth has the advantages of light weight, elasticity, good mechanical strength,HartsfieldWaterproof on the floor, good foot feeling strength, comfortable foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation, self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, it has high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor paint cloth belongs to soft floor. It is a floor coil produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor paint cloth is m ~ m, the width is mm ~ mm ~ mm, and the total thickness is mm (machine room) ~ mm (plant and public buildings)For long-term indoor use, high and medium grade products should be selected, and products produced by well-known brands and regular enterprises should be purchased as far as possible. Such products have sufficient thickness and good interlayer adhesion and are not easy to layer and curl, especially foamed leather, which gives people a comfortable and elegant feeling. If you want to use them for a short time or one-time cover, you can choose low-grade products, but many of these products are processed with waste materials, with poor flexibility, generally thin thickness and large shrinkage coefficient. When checking the appearance quality of rubber plastic floor paint cloth, it should be under scattered sunlight or fluorescent lamp, and the illumination should be ( ± LX, LM from the tested sample, conduct oblique visual inspection. First, observe whether there are cracks fractures and delaminations on the surface of the local lacquer cloth. If there are, it can be judged that the local lacquer cloth is unqualified. The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. Those that cannot be observed are excellent products and first-class products; those that are slight but not obvious are recognized as qualified. Go back to the third step for observationIf there is any missing pattern on the surface of the ground lacquer cloth, or if there is any defect of the transparent wear-resistant film on the surface, it is the first-class product and the first-class product. If there is a slight missing print or lack of film it is the qualified product, otherwise it is the unqualified product. Finally, carefully check whether there is deviation in the multi-color overprint on the surface, whether there is color difference in different parts, if the top-class product is uneven, if there are the above two defects, but if there is no obvious, it is the first-class productProducts that obviously have the above defects but do not affect the overall beauty are judged as qualified products. Finally, the appearance quality of ground lacquer cloth is determined based on the above judgment. When selecting ground lacquer cloth, first smell whether it has pungent smell. There will be a slight smell after the good coil is opened, and the smell of inferior products is stronger; secondly, calculate the use area, and the same room should be selectedCoiled materials with the same batch number, pattern and thickness. When purchasing, carefully observe the appearance quality, open a roll of ground lacquer cloth, separate the ends for a few meters, observe the surface layer of the sample, the surface layer is thick,HartsfieldIs floor leather flame retardant, the wear-resistant layer is thick, and the service time is long, and then observe whether there are cracks, fractures, wrinkles, bubbles and large defects; whether the cross section is layered and cracked; whether the pattern is open, missing, color difference and pollution.The thickness of SPC floor is mainly selected according to personal needs.Of course, the floor thickness affects the floor price, and the service life will be different, but it does not mean that the thicker the floor is, the better. We need to select according to whether the installation will affect the door closing or other s;Whether the overall effect after installation will be uncoordinated;Material budget and other aspects to select the most appropriate floor thickness.