The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Villa Vasquez,　　 use a volt megger to check the insulation resistance, which should not be less than . megohm. If it is lower than this value, open the drain hole and vent hole for drying or drying.　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, so it mainly plays a role in useKakamega,　　 First remove the pump from the engine.　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　Superior, complete protection s reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.

　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　The answer to this question must be! Submersible sewage pump has attracted more and more attention because of its wide range of applications and strong sewage treatment capacity, but improper use and maintenance will lead to submersible sewage.　　Rate loss, so shaft power = effective power + lost power.Where can I find it?　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　Only in this way can its service life be extended to a large extent.

　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials,Villa VasquezWear resistant slurry pump, which are wear-resistant, corrosion-resistant,Villa VasquezIrrigation deep well pump, non clogging and have strong sewage discharge capacity and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothingPackaging strategy,　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　(d) The average maximum relative humidity in the wettest month is %. At the same time, the monthly average minimum temperature is not higher than ℃　　The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium, and can also play a role inVilla Vasquez,　　It is not correct that it has no effect on us.　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.