Test: for the ground lacquer cloth with thin thickness, you can tear it by hand. If it can be easily torn off, the tear strength of such ground lacquer cloth can not meet the requirements. After gently rolling up and pressing down, if it can not be restored to the original state and leave an indentation, such a product has poor softness.If the layers can be torn by hand, it indicates that the product layers are not well combined, and stratification will soon occur in future use.Plastic floor paint cloth has the advantages of light weight, elasticity, good mechanical strength, good foot feeling strength, comfortable foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation moisture resistance, small water absorption good insulation, self extinguishing, easy cleaning, simple construction, it has high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor paint cloth belongs to soft floor. It is a floor coil produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor paint cloth is m ~ m, the width is mm ~ mm ~ mm, and the total thickness is mm (machine room) ~ mm (plant and public buildings)For long-term indoor use, high and medium grade products should be selected, and products produced by well-known brands and regular enterprises should be purchased as far as possible. Such products have sufficient thickness and good interlayer adhesion, and are not easy to layer and curl, especially foamed leather, you can choose low-grade products, because low-grade productsThe price is low and there are many prices to choose from, but many of these products are processed with waste materials, with poor flexibility, generally thin thickness and large shrinkage coefficient. When checking the appearance quality of rubber plastic floor paint cloth, it should be under scattered sunlight or fluorescent lamp, LM from the tested sample, conduct oblique visual inspection. First, observe whether there are cracks, fractures and delaminations on the surface of the local lacquer cloth. If there are, it can be judged that the local lacquer cloth is unqualified. The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. Those that cannot be observed are excellent products and first-class products; those that are slight but not obvious are recognized as qualified. Go back to the third step for observationIf there is any missing pattern on the surface of the ground lacquer cloth, or if there is any defect of the transparent wear-resistant film on the surface, it is the first-class product and the first-class product. If there is a slight missing print or lack of film,VeracruzLaminate flooring solid wood flooring, it is the qualified product,VeracruzLaminate flooring and imitation wood flooring, otherwise it is the unqualified product. Finally carefully check whether there is deviation in the multi-color overprint on the surface, whether there is color difference in different parts, if the top-class product is uneven, if there are the above two defects, but if there is no obvious, it is the first-class productProducts that obviously have the above defects but do not affect the overall beauty are judged as qualified products. Finally, the appearance quality of ground lacquer cloth is determined based on the above judgment. When selecting ground lacquer cloth, first smell whether it has pungent smell. There will be a slight smell after the good coil is opened and the smell of inferior products is stronger; secondly, calculate the use area, and the same room should be selectedCoiled materials with the same batch number, pattern and thickness. When purchasing, carefully observe the appearance quality, open a roll of ground lacquer cloth, separate the ends for a few meters, observe the surface layer of the sample, the surface layer is thick, the wear-resistant layer is thick, and the service time is long, and then observe whether there are cracks, fractures, wrinkles, bubbles and large defects; whether the cross section is layered and cracked; whether the pattern is open, missing, lack of film and overprint deviationDefects such as color difference, color difference and pollution.Look at the moisture content.Veracruz,Because of its special structure, solid wood composite floor has low requirements for wood and can make full use of materials, so its price is much cheaper than solid wood composite floor.Headache, dizziness, fatigue, nausea, vomiting, nausea, chest tightness, shortness of breath, eye pain, stomach pain palpitation, insomnia, weight loss, memory loss, autonomic nerve obstruction, etc.Long term inhalation by pregnant mothers is likely to cause abnormal fetuses and even death.Hartillo,UV layer: the coating formed after UV oil is cured with curing agent, which can prevent the volatilization of chemicals in the plate by UV.[]The color is gorgeous, the texture is clear, and the pattern gives people a beautiful feeling.It not only has axial drilling texture, but also has irregular thick and light parallel lines for wood texture, with clear and smooth texture and a sense of hierarchy;There are also rotary drilling textures. The wood texture also has mountain or wavy lines. The texture is beautiful, fluctuating and cool.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint,The application and marketing promotion of PVC latch floor in China has a history of ten years. From the early stage it has entered institutions and institutions such as colleges and universities, hospitals and outpatient departments in China, mainly LVT latch floor (thin thickness, the key is mm) and WPC latch floor (ordinary thin thickness: mm, mm). SPC floor is a new product in recent five years. Most LVT / WPC are made of steam pressure,Customized delivery time up to days.However, SPC floor can be formed by integrated extrusion process, and the delivery time can be shortened several times.First, pay attention to the size of the board, and try to choose a wide board with a length of cm, which is unmatched by ordinary floors.Therefore, many public spaces are also paved with SPC floors, that is to say, this reason.

The real wood floor is processed with a whole plate, with natural texture, and its section texture can correspond to the surface texture one by one;Fake solid wood floor is mostly pasted with leather or stickers on the fake floor, so the cut texture is not commensurate with the surface texture.Marketing Department,How to lay lacquer cloth?The construction procedures and methods are as follows: first, measure the structural size of the room accurately;Then cut the lacquer cloth according to the size.Note that the cutting width should be slightly larger than the required width to facilitate overlapping, matching and trimming during paving.The cut floor paint cloth shall be placed at room temperature of no less than ℃ for about hours, so that the crimped part of the floor paint cloth can be fully extended and ready for the final paving.Special adhesive shall be used for paving the floor paint cloth.Before paving, the indoor ground shall be treated first.Computer simulation printing technology is different from pure wood flooring.Reinforced floor patterns can be designed in a variety of forms.The quality of decorative layer directly affects the user&#;s use effect.The higher the price of the composite layer, the decoration layer must be the best raw material.Wear resistant layer affects the price of composite floor.The anti-wear layer directly affects the service life of laminate flooring.At present, the common laminate flooring in the wood flooring market can not achieve high strength and wear resistance coefficient but can only achieve laminate flooring.In these coatings, the wear resistance can reach revolutions.The price of land timber is an important factor determining the price of land timber. Daily maintenance does not need waxing. It can be wiped with towel or wet mop. It is widely used in indoor families, hospitals, studies, office buildings, factories, public places, supermarkets, businesses, gymnasiums and other places.SPC floor is mainly composed of a certain proportion of calcium powder and PVC stabilizer to form a composite floor paving material.It is a new material invented in response to national emission reduction, hard SPC indoor floor.SPC floor takes calcium powder as the main raw material. After plasticizing and extruding sheet, four roll calendering hot compress color film decorative layer and wear-resistant layer, SPC floor does not contain heavy metal formaldehyde with harmful substances. It is an environmental protection floor free of formaldehyde and a real formaldehyde floor.Veracruz, please provide room sizes free of charge!Obtain expert estimates to understand how many floors are needed to better determine the project budget.SPC floor is composed of thickened wear-resistant layer, UV layer color film texture layer and substrate layer.European and American countries call this kind of floor RVP (rigid vinyl plate), rigid plastic floor.The base material is a composite plate made of stone powder and thermoplastic polymer materials after mixing evenly and then extruded at high temperature. At the same time, it has the properties and characteristics of wood and plastics to ensure the strength and toughness of the floor.Wear resistant layer: PVC transparent wear-resistant layer, with a thickness of about .mm, transparent texture strong adhesion, wear resistance and scratch resistance, it has fast heat conduction and long heat storage duration. It is the preferred floor for floor heating. SPC floors are subject to biological resistance treatment, and the unique sealing of the surface layer makes the products have the characteristics of anti bacteria and antibacterial, and meet the cleaning requirements of various departments and institutions.When it comes to the choice of decoration flooring, you can think of ceramic tile marble and wood flooring. However, SPC flooring has become the first choice for people to buy Flooring in developed countries and regions such as Europe, America, Japan and South Korea, and the domestic market is gradually accepting SPC flooring. Why SPC flooring is popular? First of all, what is SPC flooring and how about SPC flooring,Now let&#;s learn what SPC floor is and how SPC floor is.SPC is the abbreviation of stone plastic composites (stone plastic composites). The main raw material is polyvinyl chloride resin. It is made by extruding SPC substrate by extruder combined with T-shaped die, and heating, laminating and embossing PVC wear-resistant layer, PVC color film and SPC substrate by three roll or four roll calender at one time. Glue is not used in the production process.