The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam,GinotepeDirect sales of welded pipe manufacturers, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Ginotepe,Check whether the manufacturer&#;s qualification, business license, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, choosing a service provider with a self built logistics fleet can reduce the transportation cost, and more importantly, ensure the timeliness of delivery. After sales service whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe the surface is smooth and flat, the weld is dense, without burr, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements, and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, bend the welded pipe for degrees, and there is no crack at the bend.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Batong, Frame line crackDetermined by the shape, the section modulus, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam, it can greatly improve the bearing capacity and save metal by % ~ %.H-section steel

Peak crack Multi channel cold rolling (cold rolling) process. Cold rolling of steel pipe is carried out on multi roll mill. Stainless steel pipes are rolled with round holes composed of variable cross-section circular grooves and fixed taper.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite,GinotepeHow much is 6 meters of one inch galvanized pipe, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, shape and chemical composition of the workpiece in the martensitic transformation zone.Encyclopedic knowledge,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.

Small longitudinal crackagentH-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, channel steel and angle steel.Steel pipes can be classified by their models:Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Ginotepe Miscellaneous scab Frame line crackThe section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.