Under the action of auxiliary devices it can transport the slurry, and because the sealing device itself is special,Salvarend higaiBooster pipeline pump, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump,Salvarend higaiCentrifugal slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beSalvarend higai,　　The system shall be equipped with a fire control cabinet.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.Oshawa,　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　 for screws that are too tight or rusted for a long time, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,

　　It is located in the middle,Salvarend higaiZD slurry pump, so it seems that many regions have good effects when using it.　　QW (WQ) submersible non blocking sewage pump needs to be equipped with a fully active water pump control cabinet under no exceptional conditions. Do not directly connect the power grid or use the knife switch to connect the power supply to ensure the normal operation of the electric pump.　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work and the interval and writetotal cost,　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.

　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.Design brand,　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　 Pipeline pump: the pipeline pump is a centrifugal pump with the same inlet and outlet in the same straight line and the same caliber. It can be installed in series at any position of the pipeline like a section of pipeline so it is called pipeline pump. It is defined and named according to the special appearance of the pump. If it is named according to the principle, the pipeline pump is a special structure　　It is located in the middle,　　The Tao part also consumes part of it.　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.