SeksadFactory lift cargo elevatorInterpretation and observation
2023-12-14 02:18:50It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Seksad,What should be done correctly after the elevator is flooded? Try to keep the elevator in a state of high front and low rear, which will help prevent water from entering the exhaust pipe and avoid damage to the converter.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases,Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod,SeksadScissor lift cargo elevator, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?
What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, the input shaft and the groove of the elevator. Fitting tolerances.The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When using it, it only needs to be connected to the power supply and the hydraulic and electrical systems basically do not need to be adjusted. Our company is engaged in all kinds of materials such as elevator factories all the year round, track grooves and operates with integrity. Welcome to call!Mechanisms: Mechanisms such as tabletops, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Word of mouth recommendation,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Prepare the foundation according to the foundation plan,SeksadGuide rail type lifting cargo elevator, pay attention to the alignment,SeksadFixed lifting cargo elevator, leveling, and alignment to ensure the level of the foundation and various requirements for use.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.
Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, carpets and floors are protected from humidity. Rusty fittings.safety requirements ,What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.After careful inspection, it was found that it was mainly caused by two reasons. One was the loss of hydraulic pressure, and the other was leakage of hydraulic valves or seals.Nowadays,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?