Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).Memphis,Under plasma arc cutting corrosion conditions, there are dust containing other metal elements or attachments of dissimilar metal particles on the surface of stainless steel. In the air, the condensate between the attachments and stainless steel connects them into a micro battery, which causes electrochemical reaction and the protective film is affected, which is called electrochemical corrosion.Flux coated welding wire (self shielded welding wire) shall be used for backing TIG welding.Aweil,Decorative stainless steel pipe: usually the outer wall is relatively bright, so its name is considered. Decorative stainless steel pipe is used for decorative purposes. The stainless steel pipe for general decorative purposes is relatively thin. Because it is different from the manufacturing process of stainless steel product pipe, the price also varies greatly. The general production process of decorative stainless steel pipe is ordinary welded stainless steel pipe. Guangdong stainless steel product pipe stainless steel product pipe: generally, the surface of stainless steel product pipe is also a bright surface, and a small number of pipes with acid pickling industrial surface. As mentioned above, because the outer diameter size, mechanical properties, acid alkali and corrosion resistance of stainless steel pipe are relatively good, Therefore, stainless steel pipes are generally used as anti-corrosion materials or hardware products in large-scale production enterprises. The production process of stainless steel pipes is one-time forming, and nitrogen protection is also added during welding.Editor's note on the causes of steel rusting: chloride ions exist widely, such as salt, sweat stains, seawater, sea breeze soil, etc. stainless steel corrodes rapidly in the presence of chloride ions even surpassing ordinary low-carbon steel. Chloride ions form complexes with Fe in alloy elements, and then being stripped of electrons and oxidized [].AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel reducing the positive potential of Fe, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates,Memphis2202 stainless steel plate, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, it is easy to form & sigma; Pay attention when using.

The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).It is generally suitable for the welding of thin plates below mm, with the characteristics of beautiful weld formation and small welding deformation.All steel with openings at both ends and hollow sections, and with a large ratio of length to section perimeter, can be called steel pipe. When the ratio of length to section perimeter is small, it can be called pipe section or tubular fittings, which belong to the category of pipe products.Direct material,Model & mdash; After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.Since the back is not filled with argon, its advantages are obvious, mainly for its simplicity and low cost, which is suitable for installation on the construction site. However, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation,MemphisStainless steel pipe welder, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites, we have successfully solved the problem that argon cannot be passed through the junction and repair port.

Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion,Memphis304 stainless steel pipe, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.Quality improvement,Water preparation, storage, transportation, purification, regeneration, seawater desalination and other water industry excellent materials. The demand is about tons.Production process of hot rolled stainless steel strip / coil: . Pickling → . High temperature rolling → . Process → . Annealing → . Leveling → ⒍ fine cutting → ⒎ packaging → . Reach customers.Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.Memphis,AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection (i.e. solid core welding wire + TIG + water-soluble paper)