Remove defective pipes within the allowable length.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment,GibalaSeamless pipe supplier, and the reproducibility of the solution is good.Gibala,Precautions for galvanized pipe storageThe core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, and the power is large, generally about KW,Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.→ wide flange and large lateral stiffness. Strong bending resistance.

Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %,Gibala12Cr2MoWVTiB alloy pipe, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min.Idler pipe: it is used for electric welding steel pipe of idler of belt conveyor. It is generally made of Q, QA, B steel and steel, with a diameter of -mm. There are certain requirements for pipe tortuosity, water pressure and flattening tests are carried out.Application characteristics of I-beam:Economic management,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment and the reproducibility of the solution is good.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties,GibalaWhat software is there for steel bar turning, chemical properties, weldability and structural size of I-beam.Passivation treatment operation of alloy pipe

Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Direct material,What is the purpose of flat steelGalvanized pipe has excellent corrosion resistance. Compared with traditional steel, its application life is longer. Secondly, this kind of pipe has strong resistance to baking. In case of critical situation, it will not lead to the collapse of building structure in a short time. In addition, this kind of pipe also has a practical advantage, that is, it is more convenient and lighter when carrying out the construction and installation. The operators save time and labor when carrying out the construction, and the operation efficiency has been greatly strengthened. In this regard, including hydrochloric acid, sodium cyanide, etc. which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Gibala,After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityThe flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.