Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.Meet the needs of architects and structural designers.Chacarita,According to the steel structure, austenite ferrite ferrite martensite and precipitation hardening note: precipitation hardening (precipitation strengthening): refers to a heat treatment process in which the metal is hardened by the segregation zone of solute atoms in supersaturated solid solution and / or the desolved particles are dispersed in the matrix. For example, austenitic precipitated stainless steel can obtain high strength by precipitation hardening at ~ ℃ or ~ ℃ after solution treatment or cold working. That is, the supersaturated solid solution of some alloys is placed at room temperature or heated to more & amp; gt;& amp; gt;Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.Guinea-Bissau,When the stainless steel pipe with solid core welding wire is prefabricated, the welded junction can usually be rotated for welding, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.When installing and welding the fixed port of stainless steel pipe, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .Model & mdash& ldquo; Cutting tool level & rdquo; Martensitic steel, an early stainless steel similar to Brinell high chromium steel. It is also used for surgical tools, which can be made very bright. Model & mdash; Ferritic stainless steel for decoration, such as automotive accessories. Good formability, but poor temperature resistance and corrosion resistance.

High frequency welding high frequency welding: with relatively high power supply, it can reach a higher welding speed for steel pipes with different materials, outer diameter and wall thickness. Compared with argon arc welding,ChacaritaCold rolled stainless steel plate, it is more than ten times its high welding speed. Therefore, stainless steel pipes for common use have a higher consumption rate. Due to the high speed of high frequency welding, it is difficult to remove burrs in welded pipes. At present, high frequency welding Welded stainless steel pipe can not be borne by chemical and nuclear industries, which is also one of the reasons.Long term professional L stainless steel pipe, the specification of a group of slightly larger formed pipes used in the production of pipe dies is about -.The product quality advantages of continuous casting billet of stainless steel pipe fittings are mainly reflected in that the non grinding rate of the outer surface of the billet except the head and tail section has reached more than %, and the total surface grinding yield has reached %. In order to achieve this goal, it is necessary to refine the molten steel, achieve low oxygen and sulfur content, do a good job in the metallurgy of the ladle and tundish, accurately determine the molten steel temperature, and realize no oxidation casting, Further reduce the inclusion content.How many?,The product quality advantages of continuous casting billet of stainless steel pipe fittings are mainly reflected in that the non grinding rate of the outer surface of the billet except the head and tail section has reached more than %, and the total surface grinding yield has reached %. In order to achieve this goal, it is necessary to refine the molten steel, achieve low oxygen and sulfur content, do a good job in the metallurgy of the ladle and tundish, accurately determine the molten steel temperature, and realize no oxidation casting, Further reduce the inclusion content.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Austenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.

At present, stainless steel backing is divided into two processes: back argon filling and non argon filling. Back argon filling protection can be divided into solid wire + TIG process and solid wire + TIG + water-soluble paper process; The back non argon filling protection is also divided into flux cored wire backing welding and welding rod (flux coated wire) backing TIG welding.For more please check,Measures to improve the welding quality of stainless steel pipe in order to ensure that the outer surface of stainless steel pipe is not damaged and purified, the maintenance of stainless steel pipe should be strengthened in each process of consumption, mainly including the following three aspects: the processing and consumption of stainless steel pipe should have a special consumption workshop (wood board is well used) , avoid the machining platform of austenitic stainless steel and carbon steel or solid overhead.Cold formed alloys can be cut and cold formed. However, due to its high strength and hardness, the alloy needs cold forming more than austenitic steel. Because of its high strength, springback should be fully considered.At low temperature ferritic stainless steel pipe has low-temperature brittleness like carbon steel, but austenitic steel does not. Therefore,ChacaritaStainless steel pipe cleaning, ferritic or martensitic stainless steel produces low-temperature brittleness, while austenitic stainless steel or nickel base alloy does not show low-temperature brittleness. Sus (Cr) and SUS (cr) of ferritic stainless steel pipe It shows that the impact value decreases sharply at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of C and N level, the embrittlement temperature is in the range of - ℃ to - ℃Chacarita,Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar. Stainless steel decorative pipe, stainless steel pipe, weak corrosion resistance, % Cr, % Ni.Good ductility, used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.With the implementation of China's reform and opening up, the national economy has achieved rapid growth, and a large number of urban houses, public buildings and tourism facilities have been built, which puts forward new requirements for hot water supply and domestic water supply. In particular, people pay more and more attention to the problem of water quality, and the requirements are also increasing. Galvanized steel pipe, a common pipe, will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances stainless steel pipe has more advantages, hot water system and water supply system that puts safety and sanitation first especially the stainless steel pipe with wall thickness of only . ~ mm. In high-quality drinking water system, it has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability. It has been proved by engineering practice at home and abroad that it is one of the new, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe, which will play an incomparable role in improving water quality and people's living standards.