After the submersible slurry pump leaves the factory, there is generally only outgoing cable, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration,BayamoQuotation slurry pump, so as to avoid a lot of impurities entering the equipment and causing pump jamming.Bayamo,　　 There is no cavitation damage and water diversion. In particular, the latter point brings great convenience to operators.　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.Baicoi,　　Many users including new practitioners of slurry pumps,BayamoSelf priming non clogging sewage pump, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　In the application of pumps often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, the first thing we think of is water. Whether it is drinking water or coefficient water even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　 absorb mud from open caissons and wells.　　With water, you can start working.Management Department,　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, this measurement is not very accurate.　　Water flow into the bearing damages the bearing.

　　.Superior quality,　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose　　 transmission device type (gearbox transmission, flat belt transmission, V-belt transmission)　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Bayamo,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume,BayamoQJ submersible pump, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and