Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.In this period, the technology of continuous rolling pipe was not mature.Posarika,How to reduce the amount of oxide scale is the key to the heating operation of seamless square tube. Especially when it's hot. Starting from the service life of tools and the surface quality of pipes, the requirements are more stringent. For example, hot furnaces are divided into heating furnace and reheating furnace according to their functions; The former is used to heat the blank from normal temperature to processing temperature; The latter is used to reheat the blank to the necessary processing temperature during processing.Generally, chemical and electrolytic methods are usedAstacus,Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours,Posarika60 hot dip galvanized pipe, improve material rate and improve product quality.For improper stamping direction, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests, the bending is compacted, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.

Stage ( & mdash; )Dimensional stability for high-precision square tubes, the required accuracy is high, so the dimensional stability must be maintained. Due to straightening in the air and slow cooling speed, so it must be cooled; Reduce quenching deformation because the square tube is slender, it is easy to deform during quenching, so its deformation must be strictly controlled. Heat treatment is a key process. In the process of quenching and cooling, the cold plasticity shall be corrected in time, which is a key step to ensure the improvement of its qualification rate. Therefore,PosarikaProduction of galvanized round pipe, hot bath quenching or cooling in oil for a fixed time shall be carried out to propose thermal correction.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Customer first,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging,Posarika76 galvanized square pipe, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welding

For transportation: water supply, drainage, sewage treatment engineering, mud transportation marine water transportation.Superior quality,Welding seamless welding seamless is to make welded elbows. After grinding and pickling, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.Performance index analysis of square tube - plasticity refers to the ability of metal materials to produce plastic deformation without deformation under load.Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Posarika,Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid alkali, etc. in the warehouse salt, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.Brinell hardness (HB) Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.