After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in useSanta Clara,　　 rotate the impeller to check whether it is flexible, and check whether the seals at the pump vent hole, water drain hole, they must be tightened.　　Commodity.Naeso,　　 Impeller protection in order to ensure the operation of the submersible slurry pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the　　Generally speaking,Santa ClaraBooster pipeline pump, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.

　　It is an auxiliary means for some on-site monitoring.　　The rotating parts of the water pump are loose and damaged.　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willHonesty is the foundation,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition,Santa ClaraQuotation slurry pump, there may be some phase to phase short circuits between stator windings so when the situation is relatively minor, the motor is only in local places

　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the tworanking,　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump high automation and performance　　Pipeline pump is also called pipeline centrifugal pump. According to the structure, pipeline pump can be divided into vertical pipeline pump and horizontal pipeline pump. Can the pipeline pump suck water? Recently,Santa ClaraSubmersible slurry pump, a customer asked this question. Most pipeline pumps have self-priming . It&#;s just that different types of pipeline pumps　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorSanta Clara,　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.