The operators are mainly plumbers and argon arc welders, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.San-Benito,　　— The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.The slab solidified on the surface continues to be rapidly cooled through the secondary cooling section until the core becomes solid,Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time,San-BenitoStainless steel water pipe 304, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.Meet the needs of architects and structural designers.In the building water supply pipe system, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.

After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.Stainless steel is a very thin, firm, fine and stable chromium rich oxide film (protective film) formed on its surface. It prevents oxygen atoms from penetrating and oxidizing, and obtains corrosion resistance. Once this film is continuously damaged for some reason, oxygen atoms in the air or will continue to separate out, forming loose iron oxide. For a long time stainless steel plate, an old brand Stainless steel pipe, has advantages in price and guaranteed quality! The metal surface is constantly corrodedThat is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.Development Curriculum,Stainless steel and alloy tool steel (C content is expressed in thousandths),San-Benito304 stainless steel pipe, such as thousandth of CrNi (i.e. .% C), stainless C & le; .%, such as CRNI ultra low carbon C & le; .%,San-BenitoStainless steel separator, such as crnimo.Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).Stop the written technical disclosure, on-site technical and safety disclosure to the on-site operators.

The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Installation requirements,There are various connection modes of stainless steel pipes. The common types of pipe fittings are compression type, compression type, union type, push type, push thread type, socket welding type, union flange connection, welding type and derivative series connection mode combining welding with traditional connection. These connection modes have different application ranges according to their principles but most of them are easy to install, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber, nitrile rubber and EPDM that meet the requirements of national standards. L stainless steel pipe, s stainless steel pipe, L stainless steel pipe and other brand products are provided for a long time. The designated products are complete and the quality is guaranteed, which eliminates the need for useGood corrosion resistance, suitable for a variety of media; The addition of Mo improves the corrosion resistance to reducing salts; It is resistant to marine and industrial atmospheric erosion, it has excellent grain boundary corrosion resistance; It can be used in pulp and paper machinery; Good processability and weldability.First of all, let's understand what stainless steel is. Generally speaking, steel that will not rust is called stainless steel, but in an academic sense, steel resistant to weak corrosive media such as air, steam and water and chemical corrosive media such as acid, alkali and salt. Also known as stainless acid resistant steel. In practical application, the steel resistant to weak corrosion medium is often called stainless steel, while the steel resistant to chemical medium is called acid resistant steel. Due to the difference in chemical composition between the two, the former is not necessarily resistant to chemical medium corrosion, while the latter is generally stainless. The corrosion resistance of stainless steel depends on the alloying elements contained in the steel. Chromium is the basic element for stainless steel to obtain corrosion resistance. When the chromium content in the steel reaches about %, chromium reacts with oxygen in the corrosive medium to form a thin oxide film (self passivation film) on the steel surface, which can prevent further corrosion of the steel matrix. In addition to chromium the commonly used alloy elements include nickel, molybdenum, titanium, copper, nitrogen, etc., so as to meet the requirements of various uses on the microstructure and properties of stainless steel.San-Benito,The recrystallization temperature changes with the shape variable. When the shape variable is %, the recrystallization temperature drops to ℃, and the recrystallization annealing temperature of cold deformed austenitic stainless steel is ~ ℃. At ℃, it needs to be kept warm for h, fully burned at ℃, and then water-cooled.Meet the needs of architects and structural designers.After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.