we use this kind of welding for priming

Meet the needs of architects and structural designers.In many construction sites, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.Cumanayagua,The inner and outer surfaces of precision stainless steel pipe and thick wall pipe shall be free of cracks, folds, crazing, cracks, rolling folds, delamination, scabs and other defects, which need to be completely removed (unless they are specially used for machining) And after removing the stainless steel pipe wall, the wall thickness and outer diameter shall not exceed the negative deviation. As long as some minor surface defects that do not exceed the allowable negative deviation do not need to be removed.AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti,Cumanayagua316 stainless steel pipe manufacturer, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content,. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing the wall thickness and lowering the grid, so as to facilitate further development. In particular, the price of stainless steel pipe is not high, so the supporting connection, the reliability and price of pipe fittings are the main factors determining its development. Domestic developers have independently developed connection technology and pipe fittings in Sichuan, Guangdong, Zhejiang, Jiangsu and other places, which is a promising pipe. The Ministry of construction and relevant departments also attach great importance to this new type of pipe. According to China technology market management promotion center and gksz [] No. document on Application & ldquo; High diameter to wall ratio and high precision stainless steel medium and high pressure water supply pipes and supporting fittings and special technology & rdquo; It is learned from the notice that the application of stainless steel pipe technology and product is of great significance to improve the grade of modern buildings in China and improve and ensure the water quality of water supply.

Model & mdash; other properties are similar except that the risk of weld corrosion is reduced due to the addition of titanium.Allowable depth of straight track: hot rolled and hot-rolled steel pipes with diameter less than or equal to mm shall not be greater than % of the nominal wall thickness, and the large depth shall not be greater than .mm; cold drawn (rolled) steel pipes shall not be greater than % of the nominal wall thickness, and the large depth shall not be greater than .mm.After molten steel casting, stainless steel pipe fittings generally adopt the same vertical vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.query,Vickers hardness stainless steel pipe Vickers hardness test is also an indentation test, which can be used to determine the hardness of very thin metal materials and surface layers. It has the main advantages of Brinell and Rockwell methods and overcomes their basic disadvantages but it is not as simple as Rockwell method. Vickers method is rarely used in steel pipe standards. Series & mdash; Martensitic precipitation hardening stainless steel.Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing the wall thickness and lowering the grid, so as to facilitate further development. In particular, the price of stainless steel pipe is not high, so the supporting connection, the reliability and price of pipe fittings are the main factors determining its development. Domestic developers have independently developed connection technology and pipe fittings in Sichuan, Guangdong, Zhejiang, which is a promising pipe. The Ministry of construction and relevant departments also attach great importance to this new type of pipe. According to China technology market management promotion center and gksz [] No. document on Application & ldquo; High diameter to wall ratio and high precision stainless steel medium and high pressure water supply pipes and supporting fittings and special technology & rdquo; It is learned from the notice that the application of stainless steel pipe technology and product is of great significance to improve the grade of modern buildings in China and improve and ensure the water quality of water supply.

When the stainless steel pipe with solid core welding wire is prefabricated, the welded junction can usually be rotated for welding, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.Interpretation and observation, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium,CumanayaguaBA stainless steel pipe, that is, fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.Usage: it is widely used in automobile industry aviation industry and other departments.Inspection: after crimping, check the crimping size with a special gauge.Cumanayagua,Production process of stainless steel pipe A. preparation of round steel; b. Heating; c. Hot rolling perforation; d. Cutting head; e. Pickling; f. Grinding; g．； h. Cold rolling; i. Degreasing; j. Solution heat treatment; k. Straightening; l. Pipe cutting; m. Pickling; n. Finished product inspection. & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.