Restate the quality of stainless steel pipe, such as stainless steel pipe, we promise & ldquo; chromium and nickel & rdquo; Penalty for false and provide quality inspection report and certificate of conformity.Corrosion resistance of decorative stainless steel pipe the price of different series of stainless steel materials varies greatly. The corrosion resistance of more economical materials can not meet the higher application requirements, and the improvement of corrosion resistance of stainless steel materials by simple chemical passivation is limited. On the other hand, the traditional passivation treatment containing chromium salt has been gradually eliminated, and the passivation treatment of stainless steel has turned to the direction of environmental friendliness. Recently, citric acid passivation and silicon treatment on stainless steel surface have become a new research direction. The former has environmental protection characteristics because its passivation solution component does not contain chromium salt. The latter has found that silicon coupling agent is chemically adsorbed on the metal surface to form a protective silicon film with cross-linked network structure. The length of discoloration time of samples after different surface treatments was compared by blue dot method, the corrosion rate of samples after different surface treatments was distinguished by brine immersion test, and the salt spray resistance of samples after different surface treatments was distinguished by neutral salt spray test, and scanning electron microscope, energy spectrometer, X-ray diffraction X-ray photoelectron spectroscopy and total reflection Fourier transform infrared spectroscopy characterized the surface films of different surface treated samples, stainless steel coil, stainless steel belt, stainless steel pipe, high price, service, on-site settlement, honest management! At present, there are few studies on the combination of citric acid passivation and silicon treatment of stainless steel. Therefore, this paper studies the difference of corrosion resistance of martensitic stainless steel Cr chemical passivation, silicon treatment and the combination of citric acid passivation and acid silicon system treatment, and discusses the corrosion resistance mechanism of different films on its surface, which can provide reference for the new direction of stainless steel surface treatment, It has certain practical guiding significance. The corrosion resistance and mechanism of chemical passivation, silicon treatment and composite treatment of martensitic stainless steel were studied in this paper. The comprehensive comparison of the research results shows that the corrosion resistance of stainless steel treated with different surface treatments is different. The corrosion resistance of the sample treated with silicon alone is better than that treated with traditional dichromate passivation. The corrosion resistance of the composite treated sample treated with citric acid passivation and acid silicon system is further enhanced than that treated with acid silicon system alone. The composite treatment of citric acid passivation and acid silicon system treatment has excellent corrosion resistance and environmental protection characteristics, and is expected to replace the traditional dichromate passivation treatment. According to the film weight test results, the surface silicon film weight of the composite treated sample after citric acid passivation and acid silicon system treatment is lower than that of the sample after acid silicon system treatment alone, indicating that the excellent corrosion resistance of the composite film not only depends on the surface silicon film, but also benefits from its double-layer film structure.Andorra,For example, the raw material difference of the three materials, such as and, which are common in the market, is more than yuan per ton.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment change the welding speed, etc. to change the molten pool temperature, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop,AndorraColored stainless steel, and the spot weld shall be polished to & deg; the slope shall be gentle,In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.The manufacturing and maintenance of equipment consume more than tons of stainless steel pipe. This kind of industry mainly adopts sanitary or grade stainless steel pipe. The sanitary seamless pipe made of imported sus and l can meet the special requirements of various media in the field of food and biopharmaceutical. Stainless steel has the advantages and good performance of stainless steel. It is widely used in kitchen equipment, workbench, utensils and medical instruments in the food industry The demand for tableware, towel hanging bracket and bracket of refrigerator in daily life is increasing.Model & mdash; Add a small amount of sulfur and phosphorus to make it easier to cut.

Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).Before connecting the pipe fittings, mark the depth on the pipe first, so as to prevent it from being inserted in place and stuck.Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, the phenomenon of reduced elongation and area shrinkage is called low temperature embrittlement. It is mostly produced on the body centered cubic structure of ferrite series.Product range,The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold areaFor example, the price of tons of goods = tons = the result example: the price excluding tax of ton of goods = a ton = ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; e.g. & Chi; Χ Χ = kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel . chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example,AndorraHow much is stainless steel, it is generally considered in the market that the price difference between burr and trimming of is yuan tons and that of is yuan tons. In fact this method is not scientific. In fact, the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.Argon shall conform to the rules of national specifications, and argon with purity of % shall be selected. If the content of impurities is too high, the maintenance effect of argon will be weakened and the weld quality will be indirectly affected.

Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, which makes up for the disadvantage of Brinell method, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation,The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme and establish quality standards.Doing well in marketing strategy innovation is a very key factor for every manufacturer joining stainless steel pipe to realize the marketing effect of market competition; However, due to the different characteristics of each market, stainless steel pipe manufacturers need to make different marketing strategy adjustments; As the saying goes, & ldquo; No matter what kind of cat it is, catching mice is a good cat& rdquo; Professional projects include: stainless steel plate, stainless steel coil, stainless steel belt, stainless steel pipe and other related businesses. Merchants who hope to have this business please. This is also true in the marketing strategy. Therefore, manufacturers of stainless steel pipes need to make marketing innovation at any time to match the changing market conditions.The operators are mainly plumbers and argon arc welders, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.Andorra,Application fields: chemical industry, construction industry.The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, so that the molten salt has strong oxidizing power, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, which is easy to be removed during acid pickling. Due to the action of high temperature, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching, firstly lift the parts basket into the tank,Andorra304 stainless steel water pipe, close the tank cover, and then lower the parts basket into the water Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable, safe, reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.