I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.With the development of steel structure buildings, only I-beam is not enough, which is easy to lose stability for load-bearing columns.St. Christopher thickened I-beamFilling: welded pipe is welded by electric welding of hot-rolled strip steel, so its influence was not as high as that of seamless steel pipe.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Ivanovo, in leg width and in waist thickness.I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.However, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.Special shaped pipe: square pipe, rectangular pipe, cap pipe, steel pipe for hollow rubber steel doors and windows welded by general carbon structure steel and Mn steel strip, mainly used as agricultural machinery components, steel windows and doors, etc. Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.Highly recommended, Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Alloy pipes can be used for heating (cooling) projects.I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, rubber, polyurethane etc., it has irreplaceable comprehensive excellent properties.

Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.system,Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃ and the solution time is min.The pipeline shall be positioned according to the drawing design, and the pipeline support shall be prefabricated according to the site conditions. Hang the wire from the th floor down and fix the support.The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.St. Christopher,Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress,St. Christopher10# steel seamless pipe, that is, thermal stress.Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment,St. ChristopherSuperalloy tube GH5188, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.