Stages needing attention in the production and manufacture of alloy tubesWhether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Temse ,Why are galvanized pipes so good?The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.Besingstock,Temse 40Cr precision alloy tube,Pass designAfter the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Carburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel, and then after quenching and low-temperature tempering, the part of the workpiece can maintain the toughness and plasticity of low-carbon steel.

The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Spiral welded pipe: it is made by rolling low-carbon structural steel or low-alloy structural steel strip into pipe blank according to the viewpoint of certain spiral line (called forming angle), and then welding the pipe seam. It can produce large-diameter steel pipe with narrow strip steel. Spiral welded pipe is mainly used for oil and natural gas transportation pipeline, and its standard is expressed by outer diameter * wall thickness. Spiral welded pipe has single-sided welding and double-sided welding. The welded pipe shall ensure that the hydrostatic test, tensile strength and cold bending of the weld meet the requirements.I-beam can only be used for beam while H-beam can be used for load-bearing column of structure.Let's see,The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.

Miscellaneous scabScheme customization, and the waist has an included angle with the horizontal axis.In order to improve the corrosion resistance of steel pipe, the general steel pipe (black pipe) is galvanized. The galvanized pipe is divided into hot-dip galvanizing and electric steel zinc. The hot-dip galvanizing layer is thick and the cost of electric galvanizing is low, so there is galvanized pipe.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Temse ,Temse Quotation of welded pipe manufacturer,Temse Welded pipe manufacturer,Greatly reduce the environmental pollution caused by abrasion, damage and blanking, and increase the labor cost of material cleaningDifference and application description between H-beam and I-beamDue to the relatively high and narrow section size of ordinary I-beam and light I-beam, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.