Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.Alajuela, and realizes the intelligent management of fire pump. We know that the purchase price of cf fire control cabinet is not low, so really　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re usingAlajuela, the slurry pump has high operation efficiency and low loss.　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　 Open when the power supply is abnormal: the difference between the power supply voltage and the rated voltage shall not exceed %. If the voltage is too high or too low, the temperature of the submersible sewage pump will rise. If the power supply is turned on abnormally, the service life will be shortened or the submersible sewage pump will burn.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainlyInstallation works,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged so we need to replace them regularly during use　　Check whether it needs to be replaced.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged so we need to replace them regularly during use　　Check whether it needs to be replaced.　　It is not correct that it has no effect on us.

　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use,AlajuelaWear resistant slurry pump, loosen the support clamp first, and say that the nut is looseCustomer first,　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, all centrifugal pumps have suction head, but the length is different. In a word, those with higher head have suction head　　With water, you can start working.Alajuela,　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?　　Submersible slurry pump shaft seal type: packing,AlajuelaLong shaft submerged slurry pump, packing and auxiliary impeller seal, mechanical seal, etc.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.