For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentPachuka,　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore,PachukaBaigang deep well pump, many pumps often have better measurement results when in use.Kuching,　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious,PachukaCarbon steel explosion-proof pipeline pump, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　A large amount of lubricating oil is stored.

　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　Submersible sewage pumps are classified as one kind of centrifugal impurities and have many forms: such as submersible and dry-type. At present, the commonly used submersible sewage pumps are WQ submersible sewage pumps, and the common dry-type sewage pumps are W-type horizontal sewage pumps and WL type vertical sewage pumps. It is mainly used to transport urban sewage and feces　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Quality recommendation, there is generally only outgoing cable and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump so we should follow the correct steps to connect.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpExcellent service,　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　 Check the water pump: it is possible that the selection of the water pump is not matched with the motor,PachukaCentrifugal slurry pump, which makes the temperature of the motor too high after long-term operation; It is also possible that the working time exceeds the specified working time of the motor. At this time, the use time and times should be strictly limited, the correct thermal protection should be selected and　　Other ysts believe that, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especiallyPachuka,　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump