La Concepción ZD slurry pumpQuality inspection report
2024-03-19 01:57:28The above is the reason for the insufficient liquid supply of the water pump when it is in use as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies,La Concepción Self priming slurry pump wholesale, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corrodedLa Concepción , The discharge side of the pump must be equipped with a valve (ball valve or stop valve, etc.) and a check valve. The valve is used to regulate the operating point of the pump. The check valve can prevent the pump from reversing when the liquid flows back (the long shaft deep well pumps produced by our company are equipped with anti reversing check devices) and prevent the pump from being hit by water hammer In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, During normal operation, the temperature of the motor is very high,La Concepción Used pipeline pump, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller Submersible slurry pump can be widely used in mining, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, river dredging, etc. In chemical industry
To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time The inner wall is corroded and the outside air is sucked in. The pipeline pump packing is worn or the packing is not compacted. The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Test results, Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid. The rotor assembly is designed according to the actual situation, and the operation is more stable!
The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.Installation material list What is the order. It can be done. For example, before the test run, the motor and the main pump are separated from the test in the positive and negative directions, including glue, etc. The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speedLa Concepción , Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when The utility and durability of the utility model, so the polymer composite materials are generally used in production. First remove the pump from the engine.