Extend service life. In fact, the submersible slurry pump is widely used in many lives and there is a very important component water seal in the pump,San Andres izapaQuotation slurry pump, so it mainly plays a role in use　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, tighten the nut with a wrench. asSan Andres izapa,　　 Check whether there is a problem with the ventilation system: check whether the fan is damaged, whether the fan rotates correctly,San Andres izapaHH slurry pump, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of timeYanacancha,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump

　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　The impeller channel reaches the outer edge.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressurePotential development,　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields,San Andres izapaPipeline pump, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.

　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.demand,　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great　　However, it can also be called submersible sewage pump.　　For example in the market, the sweeping pump for example, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.San Andres izapa,　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　It is an auxiliary means for some on-site monitoring.　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.