San MarcosWear resistant slurry pump,

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.San Marcos,　　During installation, check whether the installation position conforms to Chinese standards, which reduces the vacuum degree of the pipeline pump and affects the suction lift. Water inlet pipe　　The purpose is to avoid water leakage of the pump,San MarcosVertical heavy-duty slurry pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.West-End,　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results so it is actually the main　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops,San MarcosIrrigation deep well pump, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment

　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great　　The harm and avoidance of the reverse rotation of the slurry pump impeller the reverse rotation of the slurry pump impeller may cause the slurry pump impeller to fall off at least, or cause the damage of the whole pump at most. The reverse rotation of the slurry pump impeller mainly has the following hazards: The slurry pump impeller falls off. The connection between the slurry pump impeller and the pump shaft is a one-way screw　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidHigh quality brand,　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, feeler gauge, square ruler, copper bar, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, etc.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.

　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,Quality Assurance,　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　The submersible sewage pump operates under water. Compared with other motors, the working environment is poor. Regular inspection and maintenance are essential to ensure the 'health and longevity' of submersible sewage pumps!　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choiceSan Marcos,　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators especially　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　The fruit is also bad; When the axial flow pump is used, but the head is not too high its water output is relatively large, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one