accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Ulapan,　　 Remove the wire guard, water strainer and cut the cable from the lead and the three core cable or flat cable connector.　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willMenzel Jemil　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　 Then reinstall the equipment on the engine and install the rubber hose.　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.

　　Work,UlapanISG single stage vertical pipeline pump, no noise and vibration, and the site is cleaner.　　In fact, as far as whether the vertical pipeline pump has a suction lift is concerned, we can tell that it has a suction lift. But what you need to know is that suction range and self-priming are actually two different concepts.　　What is the order.Home page recommendation, you can refer to the following reasons.　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Information recommendation,　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　. Generally the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe, the axial force cone tube shall be selected.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump,UlapanSubmersible slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submergedUlapan,　　Troubleshooting: first increase the water pressure, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　; In practical application the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion,UlapanIrrigation deep well pump, which is convenient and flexible.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.