The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.Catago, Straight seam electric welding steel pipe (yb- is a steel pipe whose weld is longitudinally parallel to the steel pipe. It is usually divided into metric welded steel pipe welded thin-walled pipe, transformer cooling oil pipe, etc.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Ibarra,Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.Function of I-beam: where is I-beam mainly used?X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.

Plan option : Martensitic chromium alloy pipe,What is galvanized pipe Small longitudinal crackmiddleman,Last week the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials,CatagoHow much is 219 welded pipe per ton, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.

Alloy pipes can be used for heating (cooling) projects.Quality recommendation,Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionThe production methods of seamless pipe are roughly divided into cross rolling method and extrusion method. The cross rolling method is to drill the tube with a cross roll, and then extend it to the rolling mill. This method has fast production speed,CatagoWhat is the inner diameter of 8-inch welded pipe, but has high requirements for the workability of the blank. It is mainly suitable for the production of carbon steel and low alloy steel pipes. The extrusion law is to pierce the blank or ingot with a punch, and then squeeze it with a steel pipe with an extruder. The efficiency of this method is lower than that of cross rolling method. It is suitable for producing high-strength alloy steel pipe. The billet or ingot must be heated before cross rolling method and extrusion method. The produced steel pipe is called thermal correlation. Steel pipes produced by hot working can sometimes be cold worked as needed. There are two methods of cold working. One is cold drawing. In other words, pull the pipe to the pipe and tilt it to make the steel pipe gradually thinner and longer. Another method is cold rolling. The method of applying the hot smoke invented by brother to cold processing. The cold working of seamless pipe can improve the dimensional accuracy and finishing of steel pipe, and improve the mechanical properties of materials.According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.Catago,Stages needing attention in the production and manufacture of alloy tubes Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties specification scope, mold shell and software requirements, which are very simple, very easy to be replaced, and relatively low product cost. The processing time is not long enough,CatagoSeamless pipe real-time price, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams.