In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, high pressure and low temperature.Pentichton, stable operation, easy maintenance, high efficiency, long service life, and strong self-priming capacity. There is no need to install the bottom valve in the pipeline. Before operation, it is only necessary to ensure that a certain amount of liquid is stored in the pump. Different liquids can　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the mainCastro,　　Submersible slurry pump In addition, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　Through the introduction it must be avoided that the interval is relatively long, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　Will be scrapped. In addition,PentichtonSmall deep well pump, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear

　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 The pump fails to supply water or the flow is insufficient. The pump fails to supply water or the flow is insufficient. It is likely that the suction pipe has water leakage or the bottom valve has air leakage, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.Honesty and mutual benefit　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　 in addition, the noise method directly detects the noise of the equipment in the detection process but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.

　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterquality,　　 First, screw down the bolts on the side bearing pressure cap and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　The motor burns out the winding due to heat dissipation. The water pump shall be lifted and lowered at any time with the change of water level in the well. In case of water reduction or interruption, the cause shall be found out immediately or the pump shall be shut down for inspection. The cable shall not rub against the shaft wall to prevent the well water from penetrating into the motor along the cable core after the cable is worn.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time,PentichtonVertical centrifugal slurry pump, and then take relative measures to effectively solve it.Pentichton,　　Only in this way can its service life be extended to a large extent.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way,PentichtonBaigang deep well pump, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use