Saint VicenteWood floor cushion,

The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.Three layer solid wood composite floor.Saint Vicente Remove the original open putty from the edge, seal the edge again, apply primer on the whole floor and wait for drying.Advantages of solid wood composite floor;Namanga, Remove the pavement and remove dust to avoid the accumulation of crushed stones or friction coefficient floating dust on the floor surface.The shoe sole can be placed at the door to prevent broken stones or friction coefficient dust from being brought into the room.Generally, when cleaning the floor, you can wipe the road surface with cotton strips.Do not wipe the floor with wet mop or corrosive liquid (such as soap liquid and vehicle gasoline). In order to better improve the indoor air quality humidity, humidification equipment can be selected in autumn and winter to maintain the indoor air quality humidity at % - %.When moving furniture, you can&#;t push and pull the door on the ground immediately. You should stretch out and remove it with care.The bottom of furniture that moves frequently should be pasted with an eraser. Good wear resistance and stabilityThe cross-section of the floor is rubbed with a file to generate heat in the cross-section,Saint VicenteWhat brand of floor leather is good, and formaldehyde is fully volatilized (formaldehyde is accelerated at more than degrees, and you can smell the pungent smell at the same time). At this time, you can smell, generally you can smell three different levels of smell

Stable quality and not easy to damage: the solid wood composite floor plate adopts double plate composite type, and the wood chemical fiber is bent into a network structure and laminated. Various thermal stresses of wood are integrated into multiple plates to ensure the flatness and stability of the wood floor and preserve the beauty of the solid wood floorIf the scratch is shallow and the paint layer on the surface of the solid wood floor is not damaged, it can be polished with polishing paste immediately after the floor is cleaned.Because the polishing paste is mainly to maintain the luster of the floor and make the surface of the solid wood floor more and more smooth, it is not easy to cause deeper damage to the scratch area, and the scratch can also be repaired.Characteristics of fake and shoddy laminate flooringEncyclopedic knowledge,The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g,Saint VicenteWhat color does floor leather look good, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.The surface layer of SPC floor has been solved by pur Crystal Shield, with good thermal insulation performance. It will not be cold even if barefoot steps on it. It is very comfortable. Coupled with the rebound technical layer, it has good flexibility.Even if you keep bending degrees, you don&#;t have to worry about falling pain. It is especially suitable for homes with elderly and children.SPC floor will be very astringent in case of water, that is, the sliding friction will increase, and the ground anti-skid performance will be very good.It also has high wear resistance.Even if the floor is rubbed back and forth with a steel wire brush, there will be no scratches, and the service life is more than years.Moreover, with a net weight of only -kg per square meter, which is % of the raw materials of general floor. It can reasonably save the height width ratio of indoor space and reduce the bearing capacity of the floor.The SPC floor does not swell and deform, and does not need to be maintained in the middle and later stages. There is a sound insulation and noise reduction layer at the bottom and the actual effect of sound insulation and noise reduction is also very good.There are many kinds of floors used in interior decoration. Community owners who have experience in interior decoration should know that different kinds of floors have different home decoration effects. Which kind of floor is better?Let&#;s take a look at the types of solid wood composite flooring.Since the wear-resistant layer on the surface of the strengthened ground has good wear resistance, compression resistance impact resistance, fire and flame retardancy, it only needs to be cleaned with a twisted dry rag, it can be wiped with a rag and detergent.

The first kind: pungent taste. If the floor tastes like this, it means that it contains a lot of formaldehyde. You need to be careful when choosing. You&#;d better not buy it;Economic management,The double composite solid wood floor adopts double-layer solid wood pressing. It feels like pure natural wood. The installation and maintenance is very simple. It is suitable for floor heating, beautiful and generous, good reliability, and contains a small amount of indoor formaldehyde.In another case, the scar is deep, which can be supplemented with solid recovery wax, colored with paint repair pen, and then polished.After the solid wood floor is transported to the project installation site, it shall not be unpacked and installed immediately.After unpacking, it must be kept indoors for more than one week.The solid wood floor can be used only after it is adapted to the temperature and humidity of the room.Saint Vicente,The second: I can&#;t tell the taste. The domestic price of this floor is more than yuan;Solid wood flooring is not very good in terms of wear resistance, but in composite flooring, the wear resistance of solid wood composite flooring is also very different from that of reinforced composite flooring.With special components, the wear resistance of reinforced composite floor is much higher than that of ordinary solid wood floor. Anti slip, more astringent in case of water, not easy to fall