. Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.Both electric lifting and manual lifting and lowering use manual pump switch to return.revival,The fixed hydraulic loading and unloading bridge is a specialized auxiliary equipment for fast loading and unloading of goods. Its height adjustment function allows a bridge to be built between the truck and the cargo platform in the warehouse. Forklifts and other transport vehicles can directly enter the truck for batch loading and unloading of goods, and only one person can work to achieve fast loading and unloading of goods. Boarding bridges reduces a large amount of labor for enterprises improves work efficiency, and achieves greater economic benefits.Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials,　　. Embedded boarding bridge: Embedded boarding bridge, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device.In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder,revivalHigh quality fixed hydraulic boarding bridge, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, whether the site selection, pit design, and installation are in place, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.

The anti slip device of the auxiliary equipment for loading, unloading, and handling of goods applied: This equipment is made of thick steel plate welded by electric welding, which can reasonably maintain the anti slip effect and can be trusted. It is a long-term operating boarding bridge factory. Welcome to inquireBefore delivery for use, it is necessary for us to conduct static and dynamic experiments on the fixed hydraulic boarding bridge equipment to achieve different application effects. Based on the equipment environment of the elevator and the application requirements of the fixed hydraulic boarding bridge itself, selecting appropriate equipment can achieve very good application effects. It is a specialized auxiliary equipment for completing the rapid loading and unloading of goods. The fixed hydraulic boarding bridge is used indoors or outdoors, and whether it is a fixed lifting channel or a mobile lifting channel. The fixed hydraulic boarding bridge helps to ensure the safe operation of our equipment. The countertop adopts a specially designed diamond grid plate with reliable strength, which can ensure long-term use without deformation. Its diamond shaped mesh structure fully ensures excellent anti slip performance, making the forklift have better climbing and maneuverability. Even in rainy and snowy weather, normal use can still be guaranteed.Of course, due to frequent shipments long operation time, and large carrying capacity, the quality of fixed hydraulic boarding bridges has been greatly tested. Based on market analysis, the editor above provides some suggestions to enemies who have used fixed hydraulic boarding bridges and pays attention to some achievements in the application process.Safety production,　　. Embedded boarding bridge: Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device.The problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself,revivalHydraulic mobile boarding bridge, insufficient compression of the sealing ring,revivalCustomized hydraulic fixed boarding bridge, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found, Just replace it with a new one.The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixed

Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials, which will result in unexpected loss of performance in the application process.Industry management,The guide sleeve has air holes, shrinkage, and other conditions. Generally, there is a problem with the casting, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.It is understood that the mobile liquid boarding bridge is a specialized auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. The mobile liquid loading and unloading bridge is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. By using artificial hydraulic power, the height adjustment of the boarding bridge can be achieved without the need for external power supply. The adjustable length of the cable chain is used to hook the vehicle, ensuring that the boarding bridge always fits tightly with the vehicle even in case of displacement. The mobile wheel is made of solid tires, combined with brake pads to ensure safe operation.Its design is usually fully standardized as early as the structural design of buildings.revival,When using the boarding bridge for loading and unloading, load and unload according to the rated load, and do not be overweight. If overweight occurs, it will make the hydraulic system struggle during the lifting process, and even cause deformation of the hydraulic cylinder body, resulting in gaps and oil leakage outward. This requires finding a professional manufacturer for maintenance, such as Shanghai Niuli Machinery. If the deformation is severe, the only option is to replace it with a new one.In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.Anti collision block: This device can effectively protect buildings and boarding bridges from damage.