The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.Improve the positioning and pre bending steps, if necessary to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.salmon,The purity of the square tube has a great impact on the isotropic performance of the square tube. The use of secondary refining technology (including vacuum refining, ESR and ladle powder spraying) can improve the purity of the square tube, especially reduce the content of harmful impurities in the square tube, which is beneficial to improve the performance.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Nalvik,If the test results of square tubes fail to meet the provisions of product standards, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Qb square tube, qb square tube, qb square tube,salmon50 galvanized square pipe size, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.

In this period the technology of continuous rolling pipe was not mature.Empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.For transportation: water supply drainage, sewage treatment engineering, mud transportation, marine water transportation.Customer first,With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Welding seamless welding seamless is to make welded elbows. After grinding and pickling,salmonHot dip galvanized seamless pipe, sand blasting, it can not be seen that they are welded elbows.

Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.Installation conditions,Welding seamless welding seamless is to make welded elbows. After grinding and pickling,salmonHigh strength square tube, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, the narrow plastic deformation zone formed at the beginning of welding only occurs once. Moreover, due to continuous welding, the heat input is large, the heating area is large, and the plastic deformation area caused by compression is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and the heat required is small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate, and a narrow plastic deformation zone appears each time. Therefore, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding, and the longitudinal shrinkage is also smaller, The welding deformation is smaller than that of continuous filling.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).salmon,With the improvement of production quality, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different production