It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Tucson,Two main factors should be considered in the design of square pipe section: one is the safety of the section; the other is the economy of the section. For the safety of the section, we require that the ratio of waist thickness to height of H-section steel should not be less than . For H-section steel used as column, its economy is expressed by the ratio of torsion radius to its mass.Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Al Wajh,The load of impact toughness acting on the parts at a great speed is called impact load. It is specialized in products and renewable resources. Its business includes: square tube, square tube, seamless square tube, galvanized square tube and galvanized tube. The ability of metal under impact load is called impact toughness.Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, short fibers and whiskers can be added to the solder to form composites.Classification of surface treatment square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe, oiled square pipe and pickled square pipe according to surface treatment.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears folding occurs during the next rolling,TucsonHot dip galvanized steel pipe, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Inspection environment,Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel,Tucson4-point galvanized square pipe, # steel, etc; Low alloy steels are divided into q Mn, St-, etc.QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, square rectangular pipes the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.

Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Sales Department,In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design,TucsonGalvanized round pipe factory, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Hot rolled qb square tube continuous casting slab or blooming slab is used as raw material, heated by stepping heating furnace and descaled by high-pressure water into roughing mill. Roughing material enters finishing mill after head cutting, tail cutting and then computer rolling. After final rolling, it is rolled into straight hair coil through laminar cooling and coiler. The head and tail of straight hair curl are often tongue shaped and fish tail shaped, with poor accuracy of thickness and width, and there are often defects such as wave shape, hem, tower shape and so on. The coil weight is heavy and the inner diameter of the steel coil is mm.With the improvement of production quality, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.Tucson,For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Ferrous metals refer to iron and iron alloys. Such as steel pig iron, ferroalloy, cast iron etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, collectively referred to as iron carbon alloy.