At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks,SalfeldenDN200 galvanized pipe, even if the steel pipe with another large opening can be made up at one time.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Salfelden,Large diameter welded square pipe for low pressure fluid transmission, Standard No.: gbt-. Representative material: qab grade. It is mainly used to transport low-pressure fluids, such as water, sewage, gas, air and heating steam.Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Okhtyrka,Brinell hardness (HB) Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.

The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, due to continuous welding, the heat input is large, the heating area is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and the heat required is small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate, and a narrow plastic deformation zone appears each time. Therefore, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding, and the longitudinal shrinkage is also smaller, The welding deformation is smaller than that of continuous filling.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties,SalfeldenRight angle square tube, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Test conclusion,Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic,SalfeldenHot dip galvanized iron pipe, metal ceramic and metal metal welding.At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe core rod and casing for diamond core drilling.

The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.How much is it,Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Before square tube forming, the strip steel shall be leveled, trimmed, planed, surface cleaned, transported and pre bent.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Salfelden,The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeMain uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.