Hydraulic boarding axle; Streamline” The open hinge joint design increases the welding area by more than three times compared to ordinary tubular joints, effectively extending the service life and simplifying maintenance.Use a heavy crane to lift the cage and lift it from above the standard sectionYingze,The correct use of hydraulic elevators can extend their service life and also play an important role. So how should they be used?The lifting force of the scarifier is not strong or the lifting force is weak: the pressure regulation of the overflow valve does not meet the need to adjust the pressure to the required value; Refer to cleaning item above for leakage in the oil cylinder; The directional valve is stuck or leaking internally; The oil level is too low, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.Dabakala,Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.The seat belt needs to be inspected every six months, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.

Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.Now that you understand how to use a hydraulic lift, and improves the efficiency and quality of the lowering work.What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!technical serviceThe lifting force of the scarifier is not strong or the lifting force is weak: the pressure regulation of the overflow valve does not meet the need to adjust the pressure to the required value; Refer to cleaning item above for leakage in the oil cylinder; The directional valve is stuck or leaking internally; The oil level is too low,YingzeHydraulic lifting table, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged, and the joints must not be loose. All joints must be tightened.Firstly, and any violations of elevator operation should be detected

Every month,YingzeCustomized hydraulic lifting platform, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.Development Curriculum,Good stability: The overflow valve can prevent excessive system pressure during upward movement. Emergency manual valve: In case of power failure, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.Before connecting the motor to the elevator, the elevator manufacturer should first make the motor shaft keyway perpendicular to the tightening bolt. To ensure uniform force, please first screw on the installation bolts at any diagonal position, but do not tighten them. Then, screw on the installation bolts at the other two diagonal positions and tighten the four installation bolts one by one. Afterwards, tighten the tightening bolts. All tightening bolts require torque wrenches to be fixed and inspected according to the indicated fixed torque data. Elevators and lifting platforms are widely used special equipment for high-altitude operations. Its scissor fork mechanical layout ensures high stability after the elevator is lifted, with a wide operating range and high load-bearing capacity,YingzeCylinder mounted hydraulic lifting platform, making high-altitude operations increasingly large-scale and supporting multiple people working together. It makes high-altitude operations more powerful and saferHow to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.Yingze,Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.It is strictly prohibited to connect the motor of the lifting platform to the wrong power supply. It should be ensured that the voltage is V or V, and daily cleaning work should be carried out. Dust and debris on the motor should be cleaned in a timely manner.The daily maintenance of guide rail type cargo elevators should ensure that the transmission position where the grease nipple is located needs to be lubricated twice a month. For areas where grease cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.