Finally, look at the priceThe standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g,ArtemisaImitation wood floor, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary the cost is much higher if the number of wear-resistant revolutions is high.Artemisa,Fear of water and moisture: the base material of laminate floor is medium and high density board, with small relative density and large expansion coefficient. Once the reinforcing layer is filled with water after paving, if it is not wiped in time, it is easy to cause blistering and deformation due to water absorption and expansion. Its moisture resistance is not strong, and its stability is poor in humid environment.Structure: solid wood surface material, basic manual.Kidodi, See: whether the thickness of the ground lacquer cloth is full, printing layer and wear-resistant layer of the bottom layer are layered, whether there is the bottom layer,ArtemisaLaminate floor paving method, whether the thickness of the bottom layer is like a cicada wing, and whether the back of the ground lacquer cloth is black. Select substrate density From the surface coating, there are aluminum oxide, melamine and piano paint.

Melamine surface coating is generally used for wallboard, tabletop board, etc. it is used in places with low wear resistance requirements. In the flooring industry, this kind of surface coated floor is called 'false floor'Its wear-resistant revolution is only - revolutions. If it is used with high strength, the decorative paper on the surface will wear out after two or three months. The standard laminate floor will not have such a problem after years of normal use. There is no wear-resistant layer on this kind of floor decorative paper, and it is relatively smooth when touched by hand, which is the place where laymen are easy to be fooled.The performance of domestic solid wood composite floor is better than that of imported solid wood composite floor, whether it is three-layer solid wood composite or multi-layer solid wood composite floor.If the budget is insufficient or the floor heating needs to be installed at home, it is recommended to recommend domestic big brand multi-layer solid wood composite flooring (because the price of three-layer solid wood composite flooring may be higher than that of pure solid wood, and the budget is sufficient). Don&#;t be too obsessed with imported big brands, and domestic big brands may not be as good as domestic ones.Four look at the brandmarket, and the net weight per square meter is about -kg, which is less than % of the raw materials of general floor.In multi-storey buildings it has incomparable advantages of load and saving indoor space.In addition, and the upper foot is weak.Convenient installation and operation: the installation of solid wood composite floor is the same as that of laminate floor. It does not strike the ground keel. It only needs the ground leveling it has unique advantages in the renewal and transformation of old engineering buildings.Small blisters can not be repaired after damage, and can also improve the building height.

In case of large-scale immersion or partial long-term immersion in water accidentally, if there is any leveling stay, it shall be immediately sucked away with a dry rag and allowed to be dry. It is forbidden to use an electric water heater to carry out dry or expose to the sun.recommend, Environmental protection level. Check the hardness of the foundation ground.The quality of the solid wood composite board made of high-grade flowers, plants and trees can also be divided into good and bad. Therefore, it is best to select the solid wood composite floor guaranteed by a well-known brand, which can not only ensure the quality, but also deal with the problems of the store.Artemisa, Super wear-resistant. The wear-resistant layer on the surface of SPC floor is a transparent wear-resistant layer processed by high technology,ArtemisaSPC floor pavement, and its wear-resistant revolution can reach about revolutions.According to the thickness of wear-resistant layer, the service life of SPC floor is more than - years.SPC floor is a long-life floor, especially suitable for public places with large flow of people and high degree of wear.The first kind: pungent taste. If the floor tastes like this, it means that it contains a lot of formaldehyde. You need to be careful when choosing. You&#;d better not buy it; Easy to clean: medical treatment is simple, bright as a new mouth, no stains, easy to clean.The surface paint of solid wood composite floor is very good, with good wear resistance, without excessive vitality maintenance.According to statistics, the solid wood composite floor prepared for the sales market will not be waxed within years, and the wind color of automobile coating will also be maintained.This is obviously compared with the maintenance of solid wood flooring.