A non scissor type hydraulic lifting mechanical equipment used for transporting goods between floors of industrial factories, restaurants, and restaurants on the second and third floors. Professional elevator manufacturers are safe, and economical! Our products are exported to foreign countries and highly trustedThe surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.Uptar,The selection of vibration pickup points refers to the placement point of the sensor, which is used to measure the vibration amplitude of the workpiece. According to GB/T-, the acceleration sensor should be placed on the workpiece with a certain rigidity and a large amplitude, and its testing direction should be adjusted to be perpendicular to the plane where the effective zone of the vibration mode is located. Considering the complex structure of the lifting foundation workpiece and the uneven thickness of each component, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced,UptarMobile boarding bridge, they should be checked and tightenedNdioum,Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks, rollers, and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.Check the wear condition of the pinion and rack, please refer to the instruction manual for specific requirementsCheck the wear condition of the pinion and rack, please refer to the instruction manual for specific requirements

Ensure that the small gear and pressure wheel are securely fastened on the drive base plate, and check the fixing condition of the drive base plate boltsWhether the vibration aging treatment has achieved the results can be judged based on the parameter curve observation method.With the continuous development of the economy, meeting the needs of society, and increasing productivity, hydraulic cargo elevators play an important role in high-altitude operations. Hydraulic cargo elevators operate up and down,The cleaning oil for the hydraulic system must use hydraulic oil of the same brand as the system used, with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning, fully drain the system while the oil is hot.Check the protective cable condition of the cable guide frameOrganize, remove rust and repaint the structural components such as the suspension cage and guide rail frame for corrosion, and reinforce the severely corroded load-bearing members

Regularly check all wires and cables for damage. Timely bandage and replace damaged parts.quality indexThe reduction gearbox, gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.The second method is the protective layer method, which covers the metal surface of the aluminum alloy lifting platform with a protective layer to isolate the metal products from the surrounding corrosive medium and prevent corrosion. Apply engine oil,Uptar6-meter aluminum alloy lifting platform, petroleum jelly, paint, or cover the surface of steel parts with corrosion-resistant non-metallic materials such as enamel and plastic; It is not easy to apply a layer of electroplating, hot plating, spray plating, etc. on the surface of steelCheck and clean the driving gears and guide wheels of the elevator. If there is excessive wear, it is necessary to replace themUptar, correct or replace with new partsLifting and loweringThe wear rate is fast,UptarMast type aluminum alloy hydraulic lifting platform, and due to factors such as processing, assembly and adjustment of new machine components, the mating surface area is small the friction surface is rough, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period, it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point, if overloaded, it may cause damage to the components and lead to early failures.