Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Stage ( & mdash; )Laredo,The cut-off position shall match the construction and site conditions, draw the determined position and mark the cut-off line with a meter ruler or other measuring tools.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Duitama,When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.

The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.The iron filings and burrs on the cutting section shall be completely removed with a file or appropriate tools to prevent the iron filings and burrs from scratching the rubber O-ring and other accessories when connecting another part.Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Create brilliance,: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)

If there is only a single plane weld, the step-by-step back welding shall be adopted from the middle,Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes,Laredo50 galvanized pipe OD, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.Stainless steel qb square pipe for fluid transportation, Standard No.: gbt-. The representative materials are Cr crni crni cr crninb, crnimo, etc. It is mainly used to transport low-pressure corrosive media.Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Laredo,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; ), cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, it rotates and advances continuously under the action of roll and plug, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine,LaredoHot dip galvanized plastic coated steel pipe, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust agent and similar organic matter, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.