Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.Madison,The normal process flow is as follows: the round steel is perforated to form a tube embryo, then pickling is carried out, the black skin on the outer surface is washed off, and then grinding is carried out. After passing the inspection, the rolling mill or cold drawing and cold drawing are carried out. Annealing is required for wall reduction, but not for air drawing. After forming, annealing and straightening are carried out,Madison46 galvanized square pipe, and pickling is tested and stored in the warehouse. Basically, these are the processes. Better manufacturers will perform whitening treatment during annealing to make the surface treatment more beautiful. The narrow blank of square pipe can produce welded pipe with larger diameter, and the blank of the same width can also produce welded pipe with different diameter. However, the weld length increases by %, and the production speed is low. Square pipes with large or thick diameter are usually made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be directly welded with steel strip. Then after simple polishing, wire drawing is OK. Therefore, straight seam welding is mostly used for relatively welded pipes, and spiral welding is mostly used for large-diameter welded pipes.Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.muar , simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests, the bending is compacted, and many of them use sand blasting instead of sand rolling. After these steps are omitted,Madison88 galvanized square pipe, the cost is greatly reduced.Stage ( & mdash; )

If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.When processing the square tube, some processes need to heat the seamless square tube. The heating operation in the processing of the seamless square tube plays a very key role in the quality of the finished seamless square tube.Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.buildSquare tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Square tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes, large smoke tubes, alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.

Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Sincere service,Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)The strength of square tube refers to the function that the data of square tube are destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, contraction, shear and so on, because the strength is also divided into tensile strength compressive strength, flexural strength,Madison2525 galvanized square pipe, shear strength and so on. There is often a definite connection between various strengths. In normal use, tensile strength is often used as the fundamental strength gauge.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.Madison,Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.