Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, the thickness is significantly lower than the standard.Tepelena,The square tube adopts the electric contact pressure gauge to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of the strip steel.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.AmmanC. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe,TepelenaGalvanized square pipe direct selling, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.

Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.Among them, qb square tube is divided into process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency) gas welded square pipe and furnace welded square pipe are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welded square pipe.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.average method,Ferrous metals refer to iron and iron alloys. Such as steel, pig iron, ferroalloy, cast iron, collectively referred to as iron carbon alloy.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next I'll lead you to learn its cold drawing principle.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.

Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Excellent service,The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.The square tube adopts the electric contact pressure gauge to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of the strip steel.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Tepelena,Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin,TepelenaDN350 galvanized pipe,Tepelena4-point galvanized pipe, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter