cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.The side length of I-beam is small and the height is large, so it can only bear the force in one direction.death,Third, between the flange on the inner side of the sidewalk beam and the old bridge deck, the widening part of the bridge deck is poured with concrete, and the concrete of the bridge deck pavement is poured at the same time to form a carriageway. The reinforcement mesh is set on the bridge deck pavement and the widening part of the bridge deck to strengthen the overall performance. Fourth, the bridge deck expansion joint is set at the center of the cantilever beam top, and the carriageway pavement is extended and erected on the cantilever beam.What should we pay attention to in the production of alloy pipeAler Province,deathWhat is the price of plastic alloy pipe,The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.

I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.Check whether the manufacturer&#;s qualification, business license,deathHow many inches of galvanized pipe 140?, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, investigate the supplier&#;s performance and the projects served in the past. Whether there is a self built logistics fleet or not, choosing a service provider with a self built logistics fleet can reduce the transportation cost, and more importantly, ensure the timeliness of delivery. After sales service, whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe, the surface is smooth and flat, the weld is dense, without burr, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements, and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, and there is no crack at the bend.When it is used for ground heating and hot spring transportation it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Supply chain quality management,I-beam is mainly divided into ordinary I-beam light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Alloy pipes can be used for heating (cooling) projects.The specification of I-beam is expressed in cm of waist width. For example, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.Honesty is the foundation, house construction and building decoration. Its fracture will always be found in the production manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.death,deathHow much is the price of galvanized pipe per meter,I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.